User manual WESTINGHOUSE MT80 TILT INSTALL GUIDE

[. . . ] 3 Installation to Wood Stud Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation to Solid Concrete and Cinder Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing Flat Panel Screen to Wall Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Adjusting the Horizontal Position and Tilt of the Flat Panel Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Never tighten in excess of 80 in. 1. 4. 2 AA EE concrete wall Place wall mount (AA) over anchors and secure with screws (EE). fig. 1. 4. 3 concrete wall WARNING · Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster, drywall, or other finishing material as shown below. If mounting to concrete wall covered with plaster/drywall is unavoidable, plaster/drywall (up to 5/8" thick) must be counterbored as shown below. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer. INCORRECT Tighten all fasteners. SO LID CO NC RE TE AA CIN DE RB LO CK DD CORRECT concrete mount concrete CUTAWAY VIEW mount plaster/ dry wall plaster/ dry wall EE 5 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com fig. 1. 5 ISSUED: 03-02-05 SHEET #: 201-9324-1 For customer service call 1-866-287-5555. Installing Flat Panel Screen to Wall Mount 2 Note: Grommets (GG) are used to prevent easy horizontal adjustment after screen is installed. Do not attach them if you want to easily adjust screen horizontally. Place grommets (GG) onto lower hooks of left and right adapter brackets (BB, CC) as shown in figure 2. 1. Place left and right adapter brackets anywhere onto wall mount (AA) as shown in figure 2. 2. The latches (see figure 2. 3) at the bottom of the adapter brackets lock the screen onto the mount. Lock latches of adapter brackets with safety screws (FF) using wrench (HH) as shown in figure 2. 3. WARNING · Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the screen. · Safety screws must be inserted and hand tightened into each bracket and safety latch. Failure to do so can cause screen to come off mount if hit accidentally. CAUTION · Do not tighten screws with excessive force. Overtightening can cause damage to mount. · lb (2. 26 N. M. ) maximum torque. BB CC AA GG fig. 2. 3 6 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 03-02-05 SHEET #: 201-9324-1 For customer service call 1-866-287-5555. Adjusting the Horizontal Position and Tilt of the Flat Panel Screen 3 For horizontal adjustment, slide screen from side to side. If grommets are attached, the screen must be picked up and placed in new position as shown in figure 3. 1. Insert wrench (HH) through mount (AA) to adjust tension screw, shown in figure 4. 2 and detail 1, to desired tension to balance your screen size and weight. Desired tension is achieved when screen tilts easily and stays in place. Note: Tension screw is only on right side of mount Push or pull from top or bottom of screen to adjust tilt as shown in figure 4. 1. The tilt can be adjusted to a maximum of 15° forward or 5° backward. [. . . ] Place adapter brackets (BB, CC) on back of screen, align to holes, and center on back of screen as shown in figure 2. 1. Refer to step 1 to determine the proper fasteners to use. Attach the adapter brackets to the back of the screen using the appropriate combination of screws, multi-washers (O), and spacers as shown in figure 2. 2. Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver. WARNING · Tighten screws so adapter brackets are firmly attached. [. . . ]