User manual WESTINGHOUSE MT90 ARM29 INSTALL GUIDE

[. . . ] Overtightening can damage the screws, greatly reducing their holding power. · Never tighten in excess of 80 in · lb (9 N. M. ). · Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is highly recommended. A 3 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. WARNING · When installing wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete surface in the hole to be used for the concrete anchors. [. . . ] · Never tighten in excess of 80 in · lb (9 N. M. ). 2 A J N Place plate over anchors (N) and secure with screws (J) WARNING · Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster, drywall, or other finishing material. If mounting to concrete wall covered with plaster/drywall is unavoidable, plaster/ drywall (up to 5/8" thick) must be counterbored as shown below. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer. 3 Tighten all fasteners (J) J INCORRECT CUTAWAY VIEW K CORRECT mounting plate concrete mounting plate concrete plaster/ dry wall plaster/ dry wall A 4 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. WARNING · Failure to correctly mount swing arm with plastic cap at top as shown in detail 3 will result in product failure. · Improperly installed snap rings will result in product failure. · If you are uncertain that product is properly installed, call customer service. Insert holding pin (H) into wall support arm axle (C). Insert axle (C) through wall bracket(A)and lower swing arm (E). Lock axle (C) in place with holding pin (H). IMPORTANT: Be sure swing arm (E) is in correct position shown below with plastic cap at top. Next thread snap ring (I) into groove at bottom of axle (C) protruding from wall bracket (A) as shown. SNAP RING INSTALLATION: Pull snap ring (I) apart. Wind it around the tube while feeding it into the groove. Finish by snapping the end of the snap ring into groove. NOTE: Fit of axle (C) into wall bracket (A) and lower swing arm (E) will be tight. Gently tap into place with a hammer if necessary. DETAIL 3 1 groove C H H C I E A E I pre-installed snap ring groove 2 3 I Insert swivel weldment (B) through swing arm (E). Align holes in swivel bracket (D) with holes in swivel weldment (B) and secure with four M6 x 10 mm phillips screws (M) as shown. B E M B D D 5 of 9 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 05-21-04 SHEET #: 201-9226-1 For customer service call 1-866-287-5555. FOR VESA 100 MOUNTING PATTERN Use four M4 screws (R) and four bushings (S) to attach bottom plate (Q) to flat panel using phillips screwdriver (not provided). Use four center holes of bottom plate (Q) as shown below. FOR VESA 100 X 200 MOUNTING PATTERN Use six M4 screws (R) and six bushings (S) to attach bottom plate (Q) to flat panel using phillips screwdriver (not provided). Use six slots on bottom plate (Q) as shown below. Align upper end of slots with flat panel mounting holes. FLAT PANEL FLAT PANEL S R VESA 100 MOUNTING PATTERN S R Q 100 x 200 MOUNTING PATTERN Q Use four M6 screws (M) to attach top plate (P) to bottom plate (Q) using phillips screwdriver (not provided). NOTE: Top plate (P) will have one set of threaded holes on one side and a set of non-threaded holes on the other side. [. . . ] PROOF OR ORIGINAL PURCHASE ­ A sales receipt, invoice, or other proof of purchase specifying the original date of purchase within the five (5) year warranty period must be presented to obtain warranty service. This warranty extends to the original purchaser and is not transferable. EITHER REPAIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CLAIMED TO ARISE FROM BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. [. . . ]