User manual WHIRLPOOL 80182275 PRO D61 AN GEBRUIKSAANWIJZING

[. . . ] Table of contents Before using the appliance • Remove the accessories from the oven and heat it at 200°C for about two hours to eliminate the smell of protective grease and insulating materials. It is advisable to keep the window open during this operation. €¢ Before use, remove: -- stickers located on the front of the appliance and on the oven door, except the rating plate; -- cardboard protection and protective plastic film on the control panel and other parts of the appliance; -- any stickers on the accessories (e. Precautions and general advice • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given initial supervision or instruction concerning use of the appliance by a person responsible for their safety. [. . . ] After the oven has cooled down, unscrew (anticlockwise) the lamp cover. NOTE: only use 25 W 230 V lamps, type E-14, T300°C, available from our After-Sales Service. IMPORTANT: do not use the oven i without refitting the lamp cover. 5 You must not place inflammable materials or plastic utensils in the drawer compartment (placed below the oven). PROBLEM The appliance does not work POSSIBLE CAUSE The main power supply and the appliance is not electrically connected The main power supply and the appliance is not electrically connected SOLUTION Connect the product to the power supply Connect the product to the power supply The oven does not work The oven selector turned Turn the oven selector and to “0” select a cooking function The oven selector turned Turn the oven selector and select a cooking function. To The burner does not light The mains power supply and the appliance is not electrically connected The gas pipe line is closed (methane) The gas cylinder is closed (liquid gas) The openings of the burner are sealed or dirty The burner was positioned badly after cleaning The burner cap was positioned badly after cleaning The burner does not stay lit Connect the product to the power supply Open the gas pipe line Open the gas cylinder Clean the burner (See the paragraph “Cleaning and Maintenance”) Place the burner correctly after cleaning (See the paragraph “Cleaning and Maintenance”) Place the burner cap correctly after cleaning (See the paragraph “Cleaning and Maintenance”) The operation of ignition Repeat lighting operation, is carried out too quickly turning the knob to the symbol representing the small flame ENGLISH 48 Before calling the After-Sales Service 1. See if you can solve the problem on your own (see “What to do if . Switch the appliance off and on again to see if the problem has disappeared. If the fault persists after the above checks, contact IKEA After Sales Service. Always specify: • the type of fault; • exact type and model of oven; • the After-Sales Service number (the number given after the word “Service” on the rating plate) located on the back of the product; • your full address; • your telephone number. for repairs , contact IKEA After Sales Service. Failure to comply with these instructions can compromise the safety and quality of the product. ENGLISH 49 Technical data Technical data Dimension (internal) mm Width mm Height mm Depth mm Usable volume l Oven lamp W Defrost W Top + Bottom heating W Forced air W Medium grill W Grill W Turbo grill + Fan W Bottom heating + Fan W Cooling fan W Total rating W Number of functions Energy Consumption with a standard load and top + bottom heating kWh Energy Consumption with a standard load and forced air oven kWh The technical informations are situated in the rating plate on the back side of the appliance and in the energy label. The appliance must be used with the gas specified on the rating plate located on the back side of the appliance. Electrical and gas installation and maintenance of the appliance must be carried out by a qualified technician in compliance with the conditions established in the applicable regulation documents and the ethical codes. How to install the feet The appliance is equipped with 4 feet that are used for possible height alignment with the cabinets. To fit them, tilt the appliance and screw the 4 feet in the special threads located in the corners (see Fig. Installation Securing the cooker to the wall Drill two holes in the wall approximately 700 mm above and 20 mm inner the lower edge of the sides of the cooker (as shown in Fig. 1 position F), so that they are concealed by the cooker itself (see Fig. 1 ENGLISH 51 Insert part R (rawlplug) into holes F and screw hook G into part R (Fig. 4  i Class appliance: 1 Appliance Category II 2L 3B/P Type of gas Type of Injector Nominal Nominal Reduced Gas pressure used burner marking heating consumption heat mbar capacity capacity kW kW min. 10 ELECTRICAL POWER SUPPLY: 230 V ~ 50 Hz Total nominal Air necessary (m3) consumption for combustion of 1 m3 of gas 1232 l/h 21. [. . . ] €¢ Damage to the following parts: ceramic glass, accessories, crockery and cutlery baskets, feed and drainage pipes, seals, lamps and lamp covers, screens, knobs, casings and parts of casings. Unless such damages can be proved to have been caused by production faults. €¢ Cases where no fault could be found during a technician’s visit. €¢ Repairs not carried out by our appointed service providers and/or an authorized service contractual partner or where nonoriginal parts have been used. [. . . ]