User manual WHIRLPOOL 8205272
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual WHIRLPOOL 8205272. We hope that this WHIRLPOOL 8205272 user guide will be useful to you.
Lastmanuals help download the user guide WHIRLPOOL 8205272.
Manual abstract: user guide WHIRLPOOL 8205272
Detailed instructions for use are in the User's Guide.
[. . . ] MICROWAVE HOOD COMBINATION INSTALLATION INSTRUCTIONS
This product is suitable for use above electric or gas cooking products up to 36" (91. 4 cm) wide. These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in these installation instructions.
NOTES: Proper installation is the responsibility of the installer.
Product failure due to improper installation is not covered under the warranty.
Table of Contents
MICROWAVE HOOD COMBINATION SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 VENTING DESIGN SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Locate the roof damper vent cover on the top of the oven. Using diagonal wire cutting pliers, gently snip out the damper vent cover at the perforations.
A B C
A. Save the cover for possible change of venting method in the future. NOTE: Do not install damper assembly at this time.
6
Locate Wall Stud(s)
NOTE: If no wall studs exist within the cabinet opening, do not install the oven. See illustrations in "Possible Wall Stud Configurations. " 1. Using a stud finder, locate the edges of the wall stud(s) within the opening. Mark the center of each stud, and draw a plumb line down each stud center. See illustrations in "Possible Wall Stud Configurations. "
Possible Wall Stud Configurations
These depictions show examples of preferred installation configurations with the mounting plate.
No Wall Studs at Corner Holes
Figure 1
No Wall Studs at Corner Holes
Figure 2
A
MOUNTING PLATE MOUNTING PLATE
A
A
MOUNTING PLATE MOUNTING PLATE
A
B C
C D
C D A E
B
A E F
A E F
A E
NOTE: If wall stud is within 6" (15. 2 cm) of the vertical centerline (see "Mark Rear Wall" section), only ventless (recirculating) or roof venting installation can be done.
One Wall Stud at Two Corner Holes
Figure 3
Wall Studs at All Four Corner Holes
Figure 4
A
MOUNTING PLATE MOUNTING PLATE
A, D A, D
MOUNTING PLATE MOUNTING PLATE
A, D
B
D
B
A E C F
A, D A, D E C E C F
A, D E C
A. Mounting plate center markers
7
Mark Rear Wall
The microwave oven must be installed on a minimum of 1 wall stud, preferably 2, using a minimum of 1 lag screw, preferably 2 or more. Using measuring tape, find and clearly mark the vertical centerline of the opening.
Wall Venting Installation Only
Centerline Upper Cabinet Bottom
³/" (1 cm)
4" (10. 2 cm)
A
6" (15. 2 cm) 6" (15. 2 cm)
A. With the support tabs facing forward (see illustrations in "Possible Wall Stud Configurations"), align the mounting plate center to the centerline on the wall, making sure it is level, and that the top of the mounting plate is butted up against the bottom edge of the upper cabinet. NOTE: If the front edge of the upper cabinet is lower than the back edge, lower the mounting plate so that its top is level with the front edge of the cabinet.
D A B C
6. Mark the centerline 3/8" (1 cm) down from the bottom edge of the upper cabinet. Using measuring tape, measure out 6" (15. 2 cm) on both sides of the centerline, and mark. Measure down 4" (10. 2 cm) from the mark made in Step 6, and mark. Using a straightedge, draw the 2 horizontal, level lines through the marks made in steps 6 and 8. Draw the 2 vertical, plumb lines down from the marks made in Step 7 to complete the 12" x 4" (30. 5 x 10. 2 cm) rectangle. Cut a 3/4" (19 mm) hole in one corner of the cutout area. Using a keyhole saw, cut out the venting cutout area.
Drill Holes in Rear Wall
In addition to being installed on at least 1 wall stud, the mounting plate must attach to the wall at all 4 corner holes. If the holes are not over wall studs, use four 1/4-20 x 3" round-head bolts with toggle nuts; if 2 holes are over wall studs, use 2 each of lag screws and 1/4-20 x 3" bolts with toggle nuts; or if all 4 holes are over wall studs, use 4 lag screws. Following are 3 installation configurations.
A. Top of mounting plate must align with front edge of cabinet. [. . . ] Tighten bolts until there is no gap between upper cabinet and oven. NOTES: Some upper cabinets may require bolts longer or shorter than 3" (7. 6 cm). Longer or shorter bolts are available at most hardware stores.
D
A. Connect vent to damper assembly.
A
B
Overtightening bolts may warp the top of the oven. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL 8205272
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL 8205272 will begin.
