User manual WHIRLPOOL ADG 690 PROGRAM CHART

[. . . ] Before using the dishwasher, read the installation and maintenance instructions carefully! GB ADG 690 1. OVERVIEW On button Programme selection button Press the button repeatedly until the desired programme indicator lights up. START button Switches “on” when the dishwasher is operating. Switches off at the end of the programme. [. . . ] If the water hardness level falls within category 1 (soft), no salt is required. How to set the water hardness level - Switch on the appliance. - Select the 2nd programme “P2” - consult the table 1. 1 in chapter 1. - Press the START button for at least 5 seconds until the START indicator lamp flashes. - The set water hardness level is shown on the display (if present) or the START button flashes. - With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again. - The appliance must be switched off to memorise the new setting. Water hardness 1 soft 1 - 2 medium 2 medium 3 medium-hard 4 hard 4 very hard 4 extremely hard German degrees °dH 0-5 6 - 10 11 - 15 16 - 21 22 - 28 29 - 35 36 - 60 French degrees °fH 0-9 10 - 18 19 - 27 28 - 37 38 - 50 51 - 63 64 - 107 English degrees °eH 0 - 6. 3 7 - 12. 6 13. 3 - 18. 9 19. 6 - 25. 9 26. 6 - 35 35. 7 - 44. 1 44. 8 - 74. 9 Flashing frequency or display setting 1 / 1x 2 / 2x 3 / 3x 4 / 4x 5 / 5x 6 / 6x 7 / 7x Water hardness level is factory set at 3 for medium-hard water (display 4 or 4 flashes of the START button). Do not use the appliance to wash items in wood, aluminium, tin, silverware or decorated dishes (unglazed). WASH CYCLE The appliance door must be closed and the water tap open. To add dishes, open the door with caution: steam escapes. The programme resumes from where it was interrupted. The wash cycle can be stopped at any time, doing a RESET. Changing the programme in progress/Resetting - Keep the START button pressed for 2 seconds until the START indicator goes off. - The appliance is now ready to be restarted. Fitted models - Press the START/RESET button (for 2 seconds). - The appliance is now ready to be restarted. PROGRAMME END Take care when opening the door, as hot steam can escape. Press the OFF button only after the START button indicator has gone off. Unload the racks, starting from the bottom one in order to prevent any residual water dripping onto the dishes in the appliance. For better drying of dishes briefly open the appliance door before unloading, so that the steam can come out. The underside of the kitchen worktop must be protected (see “Maintenance and Installation” instructions). 5 4. PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. [. . . ] WHAT TO DO IF. . . Crockery and cutlery . . . . . . are not perfectly clean/have food residues Possible causes/solutions . . . have deposits: - regeneration salt residue - rust marks In the event of frequent use of the Eco programme 50°C (if available), from time to time select the intensive 70°C programme (if available). The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see the instructions in “Maintenance and installation”). The spray arms must be able to turn freely and must not be impeded by crockery or cutlery. [. . . ]