User manual WHIRLPOOL ADPL9874WH

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual WHIRLPOOL ADPL9874WH. We hope that this WHIRLPOOL ADPL9874WH user guide will be useful to you.

Lastmanuals help download the user guide WHIRLPOOL ADPL9874WH.

WHIRLPOOL ADPL9874WH : Download the complete user guide (5729 Ko)

Manual abstract: user guide WHIRLPOOL ADPL9874WH

Detailed instructions for use are in the User's Guide.

[. . . ] Quick reference guide Chart BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED. ECO PROGRAM INDICATOR WASH TIME DISPLAY DELAY INDICATOR RINSE AID INDICATOR SALT INDICATOR When lit, it indicates that standard program is active. Indicates the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates the time remaining until program start: “h24” if above 10 hours delay time remain and “h:mm” if below 10 hours delay time remain. If “Fx Ey” messages appears on the display, see page 9 - chapter “What to do if. . . ”. When lit, it indicates that delay is active. When lit (at the end of the cycle), the rinse aid dispenser needs to be refilled. When lit (at the end of the cycle), the salt reservoir needs to be refilled. When lit, it indicates that Multizone option is active. MULTIZONE INDICATOR WATER TAP CLOSED - Alarm Blinks when there is no inlet water or water tap is closed. When lit, it indicates that keyboard lock is active. KEYBOARD LOCK INDICATOR PROGRAM SELECTION BUTTON MULTIZONE Push “P” button (repeatedly) until selected program number is shown on the display (P1. . . Px) - see “Table of programs” - next page. [. . . ] - Close the door and press the Start/Pause button again to restart the cycle (the program resumes the cycle from where it was interrupted). To Cancel the program on running: - Press for 3 seconds the button. - (Water drains for up to 1 minute then the appliance switches off. ) To change the program in progress: - Press for 3 seconds the button to cancel the program on running. - (Water drains for up to 1 minute then the appliance switches off. ) - Press any button to switch on the appliance. Everything OK. . . 8 9 After the program is completed appliance turns into Standby mode automatically. Unload the appliance starting from the lower rack in order to avoid any residual drips of water falling onto crockery below. Maintenance and care Maintenance and care Screw on microfilter NOTE MARK!Unscrew microfilter (1), remove it (2) and remove fine sieve (3). . . 3 Filters Check and clean if necessary 2 1 Rinse under running water. . . 5 Insert 4 CLICK! 6 10 Rectifying minor faults yourself. . . Insert and screw on upper and lower arms tightly. 4 Spray arms Remove blockages/ deposits. Unscrew and remove upper arm. . . 2 1 3 Unscrew and remove lower arm. . . Clean spray nozzles under running water (use toothpicks if necessary). . . 7 5 6 8 EN -8- What to do if. . . If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance. . . salt indicator is lit Possible causes. . . Solutions. . . - Salt reservoir is empty. (After refill the salt indicator may remain lit at the end of the several - Refill reservoir with salt (for more information - see page 3). - Refill dispenser with rinse aid (for more information - see page 4). - Check whether the “Delayed start” option (if available) has been selected. If it has, the appliance will only start once the set time has elapsed. If necessary, RESET the appliance by pressing CANCEL or start the cycle immediately by pressing START. - The water tap must be fully open during water inlet (minimum capacity: 0. 5 litres per minute). - The water inlet hose must not be bent and the relative inlet filter in the water tap connector must not be dirty or clogged. - The drain hose must be fitted correctly (for high mounted appliances, leave min. 200-400 mm from the lower edge of the appliance) - see Assembly instructions. Close the water tap. rinse aid indicator is lit . . . is not working/will not start . . . shows “F6 E7” or “H2O” + Water Tap indicator - Water tap closed. - Bent water inlet hose or clogged inlet filters. . . . shows “F6 E3”/wash program ended too - Dirty or clogged filters or spray arms. early (dishes are dirty and wet) - Too little water in the dishwasher’s water system. . . . shows other fault display “Fx Ey” - Appliance has technical defect. After taking the above course of action, the fault message must be reset. The appliance is now ready to be restarted. EN -9- What to do if. . . Crockery and cutlery. . . . . . are not perfectly clean/have food residues Possible causes. . . - T little space between dishes (incorrect oo arrangement of the concave items in the rack). [. . . ] - Store the detergent, rinse aid and salt out of the reach of children. Safety warnings - The appliance is not intended for use by children or physically or mentally impaired persons, unless adequately supervised by a responsible adult capable of guaranteeing safe use of the appliance. - Do not store flammable materials in close proximity to the dishwasher. - The open dishwasher door can only support the weight of the loaded rack when pulled out. [. . . ]


Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL ADPL9874WH will begin.

Search for a user manual


Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.