User manual WHIRLPOOL AGB 231/WP INSTRUCTION FOR USE

[. . . ] Contenuto del manuale Norme di sicurezza Responsabilità del costruttore Conoscere il microprocessorE Come selezionare un programma Come avviare il programma Partenza ritardata Lettura del display L’avanzamento rapido e lo stop L’ammollo Come variare livelli, tempi, temperature Come aprire l’oblò Programmazione: concetti basilari I programmi Modifica di un programma esistente Creazione di un nuovo programma Il nome di un programma I cicli Modifica di un ciclo esistente Creazione di un nuovo ciclo Gli step I parametri degli step I tipi motore Modifica/creazione di un tipo motore Cambio della lingua Connessione a personal computer Comunicazione via modem I messaggi del display I programmi in memoria I cicli in memoria I tipi di motore in memoria Calibrazione del pressostato PAG 4 4 4 4 4 5 5 5 6 6 6 7 7 7 7 8 9 9 9 10 13 13 14 14 14 15 15 15 16 18 18 INDEX 1. Content Safety Maker’s liability Microprocessor’s acquaintance Selecting a programme Starting a programme Delayed start Display Skip & stop Soaking Setting levels, times, temperatures Door opening Programming basically Programmes Modifying an existing programme Installing a new programme The name of a program Cycles Modifying an existing cycle Setting a new cycle Steps Steps’ parameters Motor’s settings Modifying & installing motors settings Language switch Computer connections Modem communication Display scripts Stored programmes Stored cycles Stored motors settings Pressostat regulation PAG 20 20 20 20 21 21 21 21 21 22 22 22 23 23 23 23 24 24 25 26 27 28 29 29 29 29 29 29 30 30 31 32 INDEX 1. Introduction Normes de sécurité Responsabilité du constructeur Connaître le microprocesseur Comment sélectionner un programme Comment démarrer le programme Démarrage retardé Lecture du display L’avance rapide et stop Le trempage Comment changer niveaux, temps, température Comment ouvrir le hublot Programmation: concepts de base Les programmes Modifier un programme existant Création d’un nouveau programme Le nom d’un programme Les cycles Modifier un cycle existant Création d’un nouveau cycle Les step Les paramètres des step Les types moteur Modifier/créer un type moteur Changement de la langue Connexion à un ordinateur Communication avec modem Les messages du display Les programmes en mémoire Les cycles en mémoire Les types moteurs en mémoire Régulation du pressostat 33 33 33 33 33 33 34 34 34 35 35 35 36 36 36 36 37 38 38 38 40 41 42 43 43 43 44 44 44 45 46 47 47 INDICE 1. PROGRAMMAZIONE: CONCETTI BASILARI Quando si desidera costruire un nuovo programma, bisogna tenere ben presente le seguenti affermazioni: uno step è un elemento base, caratterizzato da una serie di parametri un ciclo è composto da step ordinati in sequenza un programma è composto da cicli ordinati in sequenza PRELAVAGGIO 1 00:07:24 - Uno o più dei parametri appena descritti possono non apparire, con la pressione del tasto “MENU”, se la modifica richiesta dall’Utente, non è in quel momento consentita (ad esempio: non è possibile modificare la temperatura mentre la macchina sta eseguendo una centrifuga). [. . . ] Use “+” & “-“ To scroll main menu until display shows “CYCLES SET-UP/MODIFY. Use “+” & “-“ to scroll all cycles until display shows “WASH”. Press “ENTER”, display shows “ WASH1”, use “+” & “-“ to scroll cycles available until display shows “WASH2” . press “ENTER” , display shows “WASH2”: STEP1 DRAIN”. Use “+” & “-“ to scroll steps in the sequence until display shows “WASH2 STEP4 HEATING” , press “ENTER” to select it. Use “+” & “-“ to scroll parameters until display shows “ WASH2: STEP4 HEATING TEMEPERATURE”. Press then “MENU” more times to scroll upwards to other menus. Example 5: it is required to modify the step of spin duration on cycle “SPIN3”. Display shows “DOOR OPEN” , press “MENU” , display shows “PASSWORD”, press 6 times on “START”. display shows “PROGRAMMES SETUP/MODIFICATION”. Use “+” & “-“ to scroll main menu until display shows “SPIN”, press “ENTER”. Display shows “SPIN1”, use “+” & “-“ to scroll cycles available until display shows “SPIN3”. press “ENTER” , display shows “SPIN3 : STEP 1 SPIN DURATION (40 RPM). Use “+” & “-“ to scroll steps in the sequence until display shows “SPIN3: STEP 3 SPIN DURATION (1000 rpm). press “ENTER” to select it . Display shows “MODIFY”, press “ENTER” to modify step parameters. display shows “SPIN3: STEP 3 SPIN DURATION DRUM SPEED”. Use “+” & “-“ to scroll step parameters until display shows “SPIN3 STEP3 SPIN DURATION TIME”. When required time is reached, confirm with “ENTER”. Then press “MENU” more times to scroll upwards to other menus. Also, pls bear in mind that cycles are composed by a step series. We may suppose that a washing cycle consists of the following steps: Step1 – water drain (up to 5 cms) Step2 – water load (up to 15 cms) Step3 – detergents load (i. [. . . ] STORED MOTOR TYPES Please note below listed factory installed motor types: MOTOR TYPE 1 Clockwise rotation: 24 secs Interval: 6 secs Anti-clockwise rotation: 24 secs MOTOR TYPE 2 Clockwise rotation: 15 secs Interval: 15 secs. Rinse with 7 cms level warm water and cold water level up to 18 cms Type motor 1 RINSE 2 32 32. PRESSOSTAT REGULATION If there is a problem with pressostat (wrong reading of the real water level) it is possible to E030101CW 23/11/04 regulate it. Machine on, door open, without linen and water, but in stand by, pressat the same time “+” and “-“ for more than 5 seconds. [. . . ]