User manual WHIRLPOOL AGB 584/WP INSTRUCTION FOR USE

[. . . ] VALIDITY 024_03 FROM SERIAL NUMBER 0627005545 07/2007 Instructions for installation, use and maintenance GAS COOKER AGB 579/WP AGB 580/WP AGB 583/WP AGB 584/WP INDEX Models and dimensions Data of appliances Technical data Operating instructions Construction, equipment installed and safety devices Cooking top (gas) Gas oven Gas version GN 1/1 Assembly Location Legal and technical requisites Installation Installation procedure Connecting the gas supply Gas venting Wiring Unipotential Commissioning the appliance Before commissioning the appliance Start-up Testing the power rating Checking input pressure Checking power rating using the volumetric method Checking power rating when using LP gas Checking the primary air Checking the functions Note for the installer Running the appliance on other types of gas Replacing the gas rings nozzles Replacing the oven nozzle Adjusting the primary air Replacing the nozzle of gas oven GN 1/1 Adjusting the low flame of the gas rings Adjusting the low flame of the oven page 3 Maintenance Replacing parts Gas ring ignition plung 5 Gas ring tap Gas ring thermocouple 5-6 Oven ignition plug Oven gas tap 7 Oven thermocouple Plug of ventilated gas oven 7 Ventilated gas oven gas valve 7 Ventilated gas oven thermocouple 7 Ventilated gas oven main burner 7 Fan for gas ovens GN 1/1 7 Solid top gas valve 7 Solid top thermocouple 7 Solid top ignition plug 7 page 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 7 13 7 Using the appliance 13 7 Start-up Turning a burner on and off 8 (cooking top) 13 8 Turning the gas oven on and off 13 Switching the oven light 13 8 Turning on ventilated gas oven GN 1/1 13 8 Temperature adjustment in gas oven GN 1/1 13 8 Turning the appliance off in 8 an emergency 13 8 What to do if something goes wrong or if not using the appliance for a long time 13 8 Taking care of the appliance 14 9 frequency of maintenance 9 9 WEEE Directive 9 Warning 9 9 9 9 9 9 9 15 16 024-03 - Gas cooker 2 Validity from serial number 0627005545 Dimensions 125 55 40 55 55 40 55 125 T 130 50 Bruciatore: C ø 100 G 220 G 13. 5 ±1 35±2 G 875 A 655 ±1 465 C 655 C 260 C 140 C 180 37, 5 725 37, 5 200 400 800 200 AGB 579/WP 125 55 40 55 55 40 55 125 T 130 50 G 13. 5 ±1 35±2 G 220 C 655 C 260 A 655 ±1 465 875 C C 180 200 140 400 800 200 37, 5 725 37, 5 AGB 580/WP 125 55 40 55 55 40 55 55 40 55 125 T 130 50 215 G 215 G 13. 5 ±1 35±2 G 220 C C 655 C C 260 A 655 ±1 465 875 C C C 180 200 140 400 1200 400 200 37, 5 1125 37, 5 AGB 583/WP A G T Off-take Gas connection Data plate 024-03 - Gas cooker 3 Validity from serial number 0627005545 215 G Dimensions 125 55 40 55 55 55 40 55 125 T 130 50 Bruciatore: C ø 100 G 13. 5 ±1 35±2 G 200 220 C 655 C A 655 ±1 465 875 C C 180 200 140 400 1200 400 37, 5 1125 37, 5 AGB 584/WP A G T Off-take Gas connection Data plate 024-03 - Gas cooker 4 Validity from serial number 0627005545 260 215 G 2 - CHARACTERISTICS OF THE APPLIANCES These appliances are used for professional purposes. Installation, repair and use must be carried out by expert personnel. These instructions for installation are for our gas kitchens set up for the category in the table on page 6. The data plate is located on the front part of the appliance (on the control panel). CAT/KAT II2H3B/P II2H3+ II2H3+ II2L3B/P 0051 II2ELL3B/P TIPO/TYPE MOD. [. . . ] room housing the appliance may affect the combustion air supply. Once the alterations have been completed, Adjusting the low flame of the gas the appliance and its functions should be thoroughly rings (Fig. Referring to the “TECHNICAL DATA” table, set the low flame screw (D) as follows: Running the appliance on other types - if the appliance is to run on LP gas, tighten the low flame screw as far as it will go; of gas - if the appliance is to run on natural gas, turn the low flaWhen changing to another type of gas, e. g. from natural to me screw: LP, or to another gas group, consult the “TECHNICAL DATA” table to make sure you use the appropriate nozzlzes ● read off the setting in It/min which corresponds to for the main burner. the heat value (calculated by the “Volumetric Method”) The nozzles for the cooking top burners for different types in the Gas Flow Setting Table (2); of gas, marked in 100ths of mm, are in a case supplied ● start the appliance up according to the instructions; with the appliance. If injectors are not available please ● after allowing the appliance to run for 45 minutes, contact the factory with model and serial number written turn the knob to low and set minimum by turning screw on technical data sticker. (20) (to the right = gas flow decreases; to the left = When the appliance has been transformed or adapted, regas flow increases). check its functions as described in paragraph "Checking Adjust the gas flow. the functions". Replacing the gas ring nozzles (Fig. 2) To change nozzle (C), remove the knobs and loosen the control panel fixing screws. Remove the control panel, disconnect the ignition lead and unscrew the nozzle from the nozzle holder with a spanner. Replace with a new nozzle (see “TECHNICAL DATA” table. After fitting the nozzle, reset primary air distance “A” (see “TECHNICAL DATA” table). Adjusting the low flame of the oven (Fig. 3) by two or three turns after having removed the knob and the control panel cover. Light the burner and keep it lit for at least 10 minutes with the knob in the MAX position, then put the knob to Min and tighten screw H until a reduced but steady, even flame is obtained (the flame must warm the thermocouple even on low). 024-03 - Gas cooker 9 Validity from serial number 0627005545 MAINTENANCE The following maintenance programme should be carried out at least once a year: - Check that all the safety and setting devices are working properly; - Check that the burners are working properly with regard to: - ignition - combustion safety; - Check the functions of the appliance as described in paragraph "Checking the functions" page 9. If the main burner needs cleaning, proceed as follows: a ) Gas rings: remove the pan support, the flame distributor, the crown and the burner supports; b) clean the parts with water and detergent, rinse and dry; c) when reassembling the parts, make sure you replace them in the right order. Cleaning the oven burner To gain access to the oven burner, remove the floor (from inside the oven cavity). 3) and remove the burner by pulling it forwards. Clean the burner with water and detergent; to unblock the holes, use a suitably sized prong. Oven gas tap (A - Fig. 3) Loosen the nuts on the thermocouple and on the gas pipes, draw the thermostat bulb out from the supporting clips inside the oven cavity and replace the tap with a new one. Oven thermocouple (L - Fig. 3) Remove the floor, unscrew the nut on the tap and the burner and replace the thermocouple. After having disassembled the various pieces, the control panel cover must be replaced. Plug of ventilated gas oven (Fig. [. . . ] For complete shutdown, turn the knob to position (0); in this position the pilot burner also goes out. Turning the appliance off in an emergency In an emergency turn off the appliance according to the instructions; close the gas supply tap or disconnect the power supply. What to do if something goes wrong or if not using the appliance for a long time If the appliance is not to be used for a long time, or if it breaks down or works incorrectly, close the tap to the gas mains located outside the appliance and disconnect from power supply. If anything goes wrong, call the aftersales department. Should the piezo spark lighter not work properly, the oven may be lit manually. After having opened the door, put a lit match near the hole in the oven floor. At the same time turn the knob counter-clockwise, keeping it pressed down, to the thermostatic position 7. [. . . ]