User manual WHIRLPOOL AGB 627/WP INSTRUCTION FOR USE

[. . . ] m3/h II2E+3+ II2H3B/P I2E II2H3B/P II2H3+ I3B/P I3+ GAS/GAZ P mbar P mbar P mbar P mbar P mbar P mbar P mbar P mbar P mbar P mbar P mbar P mbar G30 30 30 28 30 50 28 50 30 28 30 28 G31 30 37 37 30 50 37 50 30 37 30 37 G20 20 20 20 20 20 20 20 20 - G25 25 20 25 SE IT ES NL DE FR AT LU EE EE NO CY LV LV MT LT LT CY IS HU BE CH FI CH IE DK PT GB GR CZ SK SI Predisposto a gas: - Gas preset: - Prevu pour gaz: Eingestelt für Gas: - Preparado para gas: - Geschuckt voor: V AC kW Hz MADE IN ITALY THE APPLIANCE MUST BE CONNECTED IN COMPLIANCE WITH THE LAWS IN FORCE AND INSTALLED IN A WELL-VENTILATED ROOM. READ THE INSTRUCTION MANUALS BEFORE INSTALLING AND USING THE APPLIANCE. THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL. 3 - TECHNICAL DATA Model Description Electric grill salamander - Mobile head AGB 625/WP Electric grill salamander - Mobile head AGB 627/WP Electric grill salamander - Mobile head Dimensions mm. (LxPxH) 550 x 370 x 440 800 x 370 x 440 600 x 530 x 605 TABLE 1 Model Power kW 2. 5 AGB 625/WP AGB 627/WP Voltage V 230V 50Hz 230V 50Hz 230V 50Hz No. [. . . ] WE SHALL NOT BE HELD LIABLE IF ACCIDENT PREVENTION STANDARDS ARE NOT COMPLIED WITH. 4. 2 Electrical connection The unit is set up for operation on alternating current at the voltage shown on the technical data plate. The earth wire in the power cord can be identified by its yellow and green colours. Place a plug on the cord which is suitable for the load indicated on the technical data plate and connect it to an adequate electrical outlet. If you want to connect the appliance directly to the electrical mains, it is necessary to place an omnipolar switch between the mains and the appliance, with a load size which complies with current regulations. The yellow and green earth wire must not be interrupted. In any case, the power cord must be placed in such a way that at no point does it reach a temperature 50% greater than the ambient temperature. 5 - SET-UP FOR OPERATION 5. 1 Start-up The user is reminded to check that installation of the appliance has been properly carried out. The manufacturer will not be liable for guarantees and/or damage for poor installation, incorrect maintenance or improper use. 1 5. 1. 1 Using the energy regulator AGB 625/WP : 1 heating zone controlled by 1 energy regulator. AGB 627/WP: 2 independent heating zones each controlled by 1 energy regulator. Rotate the knob of the energy regulator (Fig. Keep in mind that the minimum is obtained in the thinnest part of the comet-shaped icon and the maximum in the wide part. An indicator light indicates that the heating element is on. the heating element will By turning the knob to the position always be on. Do not use the appliance in this position for more than 20/30 minutes continuously. • 070_03 - ELECTRIC GRILL SALAMANDER 07/2007 6 · 10 5 - SET-UP FOR OPERATION 5. 2 Safety, cleaning and repair rules • Before performing any operation, disconnect the appliance form the electrical network. No particular maintenance is required; it is only necessary to check the condition of the conductors, the controls and the electrical heating elements. - Periodically check the condition of the power cord; - If any abnormalities are discovered, have it checked by qualified personnel; - Be sure to disconnect the electrical power supply if the appliance is not going to be used for a long period of time. 6. 2 The 2002/96/EC (WEEE) Directive: information to users This informational note is meant only for owners of equipment marked with the symbol shown in Fig. A on the adhesive label featuring the technical specifications applied on the actual product (the label also giving the serial number). This symbol indicates that the product is classified, according to the regulations in force, as an item of electrical and electronic equipment and conforms to EU Directive 2002/96/EC (WEEE) meaning that, at the end of its service life, it must be treated separately from domestic waste, i. e. it must be handed in free of charge to a separate waste electrical and electronic equipment collection centre or returned to the reseller when buying a new equivalent item of equipment. The user is responsible for delivering the unit at the end of its life to the appropriate collection facilities. [. . . ] Remove the electrical connections on the heating element and loosen the fastening screws, remove the heating element for replacement by unscrewing it form the lower part. To re-install follow the operations in reverse order, taking care to replace the electrical connections perfectly. Energy regulator and indicator light: Remove the control panel by loosening the 4 visible screws. NOTES 070_03 - ELECTRIC GRILL SALAMANDER 07/2007 7 · 10 6 - APPENDIX: ELECTRICAL DIAGRAMS AGB 625/WP R1 2 B1 P1 4 P2 S S H1 mA 1 2 3 230V L1 N PE mA B1 H1 R2 Line in terminal board Energy regulator Indicator light Heating element 3000 W Power: 3. 0 kW 230 V 070_03 - ELECTRIC GRILL SALAMANDER 07/2007 8 · 10 6 - APPENDIX: ELECTRICAL DIAGRAMS AGB 627/WP R1 R1 2 B1 P1 4 P2 S S 2 4 P1 P2 S S H1 B1 H1 mA 1 2 3 400 V 3N L1 N PE mA B1-B2 H1-H2 R1-R2 Line in terminal board Energy regulator Indicator light Heating element 1500 W Power: 3. 6 kW 230 V 070_03 - ELECTRIC GRILL SALAMANDER 07/2007 9 · 10 WARNING THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR ANY INACCURACIES IN THIS BOOKLET DUE TO COPYING OR PRINTING ERRORS. DUE TO ITS POLICY OF CONTINUAL PRODUCT IMPROVEMENT, THE MANUFACTURER RESERVES THE RIGHT TO MAKE ANY CHANGES DEEMED NECESSARY. [. . . ]