User manual WHIRLPOOL AKT424WH

[. . . ] -The appliance must be disconnected from the power supply before carrying out any installation work. -Installation and maintenance must be carried out by a qualified technician, in compliance with the manufacturer s instructions and local safety regulations. Do not repair or replace any part of the appliance unless specifically stated in the user manual. TECHNICAL INFORMATION FOR THE INSTALLER • • This product can be embedded in a worktop 20 to 60 mm thick. If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. [. . . ] Light up the burners and turn the knobs from max position to check flame stability. to minimum position C C A B C 5019 319 01838 Manufacturer: Whirlpool Europe S. r. l. Borghi, 27 21025 Comerio (VA) ITALY ELECTRICAL CONNECTION WARNING WARNING This operation must be performed by a qualified technician. • REPLACING THE INJECTORS (see the injector table in the Instruction) • • • Remove grids (A). Using a socket spanner of the appropriate size unscrew the injector (C), unscrew the injector to be replaced. • Replace it with the injector suitable for the new type of gas. • Re-assemble the injector in (D). • If you have a multiple crown burner use side spanner to replace the injector (E). Before installing the hob, remember to affix the gas calibration plate supplied with the injectors in such a way that it covers the existing information relating to gas calibration. The electrical connections must L comply with local regulations. Earth • The earthing of this appliance is (yellow/green) compulsory by law. • IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate. ASSEMBLY After having cleaned the perimeter surface, apply the supplied gasket to the hob as shown in the figure. ADJUSTING MINIMUM GAS SETTING OF TAPS Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction. NOTE: the power supply cable must be long enough to permit its upward extraction. To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance with the thickness of the worktop (see the following figures). Top 20 mm Top 40 mm 20 40 To ensure that the minimum setting is correctly adjusted, remove the knob and proceed as follows: • tighten screw to reduce the flame height (-); • loosen screw to increase the flame height (+). The adjustment must be performed with the tap in minimum gas setting position (small flame) . • The primary air of the burners does not need to be adjusted. • At this stage, light up the burners and turn the knobs from max position to minimum position to check flame stability. Upon completion of adjustment, reseal using sealing wax or an equivalent material. Top 30 mm 30 Top 60 mm 60 REFERENCE TO LOCAL REGULATIONS Ensure that the installation and gas connections are performed by a qualified technician, following the manufacturer's instructions and in compliance with current local safety regulations. ADJUSTMENT TO DIFFERENT TYPES OF GAS WARNING This operation must be performed by a qualified technician. AFTER-SALES SERVICE Before calling the After-Sales Service, make sure you can give the following information: -type of fault or problem; -exact model (written on the label affixed to the instruction/warranty); -service number that follows the word SERVICE on the rating plate under the hob and on the label affixed to instruction/warranty; -your complete address and phone number. -If any repairs are required, please contact an authorised After-Sales Service, as indicated in the warranty. If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob, change the injectors. Remove the information label and keep it with the instructions booklet. Use pressure regulators suitable for the gas pressure indicated in the Instruction. [. . . ] IMPORTANT: WHEN THE HOB IS IN USE, THE ENTIRE HOB AREA MAY BECOME HOT. • To ignite one of the burners, turn the relative knob anti-clockwise to the maximum flame setting. • Press the knob against the control panel to ignite the burner. • After the burner has ignited, keep the knob pressed for about 5-10 seconds to allow proper device operation. [. . . ]