User manual WHIRLPOOL AWOD4814

[. . . ] Spin Speed rpm Cotton 95°C Cotton 40 - 60°C Jeans 40°C Synthetics 30 - 40 - 60°C Delicates 30 - 40°C Daily load 40°C Quick wash 30°C Wool/Handwash cold - 40°C 8. 0 95°C 8. 0 40 - 60°C 4. 0 40°C 3. 0 30 - 40 - 60°C 1. 5 ❉ ❉ ❉ ❉ ❉ — — — — — — — Yes ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — — — ❉ ❉ ❉ — — — — — — — — ❉ ❉ ❉ ❉ ❉ — — — — — — — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ max. Yes max. Yes 1000 1) Normally soiled garments made of artificial fibres (like polyester, polyacryle, viscose etc. ) or their blends with cotton. Yes max. 30 - 40°C Curtains and delicate clothing, dresses, skirts, shirts and blouses. Yes 1000 1) 4. 0 40°C 3. 0 30°C / 20 - 40°C 1. 0 Lightly to normally soiled robust laundry made of cotton, linen, artificial fibres and their blends. Make sure to wash only similar colours together in one wash load. Yes max. Shortly worn clothing made of cotton, polyester, polyamide and blends with cotton. Brief programme to refresh your laundry. Textiles made of wool, linen, viscose or silk (respect care label!) marked as hand-washable or machine-washable. [. . . ] • • • • Select programme, temperature and options. Press the “Start delay” button to select a delay time of 1, 3, 6, 9 or 12 hours. Press the “Start/Pause” button . The delay time indicator goes off when the programme starts and it is replaced by the programme flow bar indication. • Once having pressed the “Start/Pause” button “Start delay” button. To cancel the “Start delay” . . . before you press the “Start/Pause” button • : , the delay time can be changed by pressing again the Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15 °C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption data. The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also “Troubleshooting Guide” in your Instructions for Use). * Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature. ** *** To reduce the water temperature, some cold water is added at the end of the main wash cycle before the water is drained. Automatic adaptation of programme duration after detection of wash load. PROGRAMME END • The “Door open” indicator completely to save energy. Turn the programme selector to the “Off/O” position. Leave the door ajar to allow the drum to dry. After about a quarter of an hour, the washing machine will switch off LOAD LAUNDRY, ADD DETERGENT AND SELECT THE PROGRAMME Load the laundry, close the door and add detergent as indicated on the front page and as described in the chapter “Detergent and Additives” in your Instructions for Use. Turn the programme selector to the desired programme and temperature. The “Start/Pause” indicator blinks. The washing machine is designed to save energy, therefore, if you have selected a programme but do not start it within about a quarter of an hour, it will switch off automatically. [. . . ] Press the “Start/Pause” button again. The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme. to pause the Turn the programme selector to another position or press the “Reset” button . [. . . ]