User manual WHIRLPOOL AZB 9780/1 PROGRAM CHART

[. . . ] A fast blinking lamp indicates a wrong selection is made (incompatible options). Press the button again to cancel the option. The drying programme is started by pressing the “Start (Pause)” button. Changing programme selection: If the programme selected is changed during drying, the dryer stops. [. . . ] 9. 0 kg X X X X X X X X 160 135 Iron dry Iron dry* X X X X X X X X 130 110 VW Extra dry Extra dry Synthetic, mixed fibre or cotton easy care (ironing not required) laundry X X – X X X X X 95 70 Synthetic Cupboard dry Iron dry Cupboard dry* Synthetics Max. 4. 5 kg X X – X X X X X 70 50 Iron dry X Laundry made from synthetic fibres such as polyamide, nylon, polyacrylic, etc. 2. 5 kg Cotton – synthetic blend 3. 0 kg Cotton 3. 0 kg Textiles made of silk 2. 5 kg Synthetic 2. 5 kg X – X X X X X 60 45 Special programmes V Delicate Plus Delicate plus X X – X X X X X 85 70 Mixed load Mixed load X X – X X X X X 80 60 Jeans Jeans Jeans, working trousers and jackets. X X – X X X X X 80 60 Silk Silk Blouses, shirts and T-shirts. X X – X X X X X 85 70 Sport Sport Sport clothes, functional underwear, running tights. X X – X X X X X 85 70 Airing Laundry is aired, refreshed and loosen up for 30 minutes without heating. All textiles. Airing Drying time 10’ 20’ 30’ 40’ 50’ 60’ 70’ 80’ 90’ 100’ 110’ 120’ – – – – X X X X 30’ – Drying items Completes drying (suitable for all fabrics) X X – X X X X X 10’ 20’ 30’ 40’ 50’ 60’ 70’ 80’ 90’ 100’ 110’ 120’ *Test programmes according to EN61121, tested with maximum rated load capacity. 2  HOW TO PROCEED IF… . . . you want to check the dryer yourself first: (If your machine is not functioning correctly, please check the following points before calling the customer service – also refer to relevant chapter in the Instructions for use) Drying takes too long / Laundry is not dry enough  Has the correct drying programme been selected? Has the cycle been interrupted (door opening, full water container)? Was the inserted laundry too wet (washing machine spin speed less than 1000 rpm)? Is the lint filter dirty (filter indicator light on)? Is the heat exchanger dirty (for more information, refer to the Instructions for use)? Is the “End” and “Anticrease” indicator lamp lighting up?The drying cycle is complete and the laundry can be taken out.  If the drying result does not meet your expectation, select a more dry programme or use the dryness adjustment option (if available) to optimize the drying result. Sort the laundry after thickness and material and dry again.        Is the plug properly inserted into the mains electricity socket?Has the “Start (Pause)” button been pressed?Has the start delay option been selected? Has the water container been inserted correctly? Is the heat exchanger clean and inserted correctly? Has the heat exchanger been inserted correctly? Have all lint on the heat exchanger seal and the door seal been wiped away? Has the water container been inserted correctly? If the direct drain connection is used, is it tight? Is the dryer leveled? The dryer does not operate (after a power failure, always press the “Start (Pause)” button) Filter, water container indicator lamp on Water droplets underneath the dryer . . . you want to care of and clean your dryer: Clean the filter at the end of every cycle  Brush lint using a soft brush or your fingertips.  Pull the handle to remove the water container. [. . . ] The key lock function is still active even when the selector knob is turned to “off” position or the door is opened. The function has to be deactivated.  Sometimes the programme may finish before the selected “Finish in” time has expired (e. g. In this case, the dryer will tumble the laundry regularly to keep it fresh, until the selected “Finish in” time has expired. During tumbling, the display will show an animation. [. . . ]