User manual WHIRLPOOL HB 3 IH PROGRAM CHART

[. . . ] To activate the function, select a cooking zone with the button “B” and press the button “D”. A P appears on the display. Left round induction cooking zone Ø 210 mm Central round induction cooking zone Ø 145 mm Right round induction cooking zone Ø 180 mm Display 4 Important: To avoid permanently damaging the glass-ceramic top, do not use: - Pots with bottoms that are not perfectly flat - Metal pots with enamelled bottom. Any aesthetic defects (scratches, marks, etc. ) must be reported at the time of installation. H RESIDUAL HEAT INDICATOR. After the cooking zone is switched off, the residual heat indicator “H” remains on or flashes, alternating with “0” until the hob temperature falls to an acceptable safety level. Important: The hob's safety features include an automatic switching off function. [. . . ] Technical data is given on the rating plate located on the underside of the hob and is also specified here: 744 TYPE: PLEAN 230 V~/400 V 3N ~ 50 Hz 5. 8 kW TYPE: PLEAN 230 V ~ 50 Hz 5. 8 kW (only for UK) A F E A B C On/Off Heat setting increase Heat setting decrease D E F Fast boil Child safety Timer 324 Declaration of conformity CE • • • This cooktop is suitable for contact with foodstuffs, and complies with EC regulation no. 1935/2004 The appliances are designed solely for use as cooking appliances. for room heating) is considered improper and potentially dangerous. The appliances are designed, built and sold in compliance with the safety standards of the “Low Voltage” Directive” 2006/95/CE (which replaces the directive 73/23/EEC and subsequent amendments) the protection requirements of Directive 89/336/EEC pertaining to “Electromagnetic Compatibility”. the requirements of Directive 93/68/EEC. • • C B D CAUTION: Before switching on the hob, deactivate the CHILD SAFETY DEVICE by pressing button “E”. To switch the hob on, keep button “A” pressed for approx. The 3 cooking zone displays show “0”. If within 10 seconds none of the cooking zones are activated, the hob switches off automatically as a safety precaution. Press one of the buttons “B” corresponding to the cooking zone you intend to use. Select the heat setting required with buttons “B” or “C”. Important: After setting the heat level, the selected cooking zone is deactivated within 60 seconds if no recipient is placed on it. To change the heat setting of a plate, press buttons “B” or “C”. Press buttons “B” or “C” at the same time to cancel the selection. Press button “A” to switch off all activated plates. The CHILD SAFETY function is switched on by holding down button “E” until a dot lights up above the function button. The Child Safety function locks all the hob's other functions, with the exception of the On/Off button “A”. The function remains on even after the hob is switched off and on again and can be deactivated by pressing button “E” again until the dot above the function button goes off. Energy saving tips • • • • • Use pots and pans whose bottom diameter is equal to that of the cooking zone or slightly larger. If possible, keep pot lids on when cooking. with little water in order to cut down cooking time. A pressure cooker allows you to save even more energy and time. 5019 619 01077/B To get full satisfaction from the hob, please read these instructions carefully and keep them for future consultation. Make sure you place the pot or pan in the centre of the cooking zone outlined on the glass-ceramic induction cooktop. Induction cooktops only work when used with pans and pots made of magnetic material. Suitable pans can be enamelled and made of cast iron or special steel: cookware manufacturers mark their products with the word “INDUCTION” on the base to indicate that they are compatible with induction cooktops. • Induction cooktops DO NOT WORK with cookware made of normal stainless steel, glass, ceramics, copper or aluminium (fig. [. . . ] This could hinder the ventilation and cooling of the electronic module and decrease the effectiveness of the hob. Electrical connections Electrical connection must be made before connecting the appliance to the electricity supply. The appliance must be installed by a qualified electrician who is fully aware of current safety and installation regulations. Specifically, installation must be carried out in compliance with the regulations of the local electricity supply company. Make sure that the voltage shown on the rating plate is the same as the power supply voltage in your home. [. . . ]