User manual WHIRLPOOL HOB G22 S PROGRAM CHART

[. . . ] Check whether the hob has been damaged during transport and remove any protective film from the appliance parts. This hob is designed solely for household use for cooking food. Any other use (such as heating rooms) is to be considered improper and, as a consequence, dangerous. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given initial supervision or instruction concerning use of the appliance by a person responsible for their safety. [. . . ] In the case that you intend to install an oven beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. The manufacturer declines all liability if another brand oven is installed beneath the hob. Before installation, make sure that: the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the rating plate and injector table). The outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations. Combustion products are discharged outdoors through specific hoods or wall and/or window mounted electrical fans. PROVISION FOR VENTILATION ROOM VENTILATION To ensure correct operation of the appliance, the room size in which it is to be installed shall be in accordance with AS5601. This room must also be continuously ventilated, fresh air should flow through permanent openings in walls to outside or to an adjacent non-inhabitable room as detailed is AS 5601. These permanent openings must be made in such a way that it cannot be obstructed from either side of the wall, also they should be protected by plastic grids, metallic mesh, etc. , taking care not to reduce the air vent effective area mentioned above and located near floor level and positioned so as not to interfere with the operation of the exhaust system, the minimum cross section of these permanent openings is set by AS5601. • - OVERHEAD CLEARANCE Range hoods and exhaust fans shall be installed in accordance with the manufactures instructions. However, in no case shall the clearance between the top of the highest burner of the cooking appliance and the range hood be less than 600mm or, for an overhead exhaust fan, 750mm Any downward facing combustible surface less than 600mm above the top of the highest burner shall be protected for the full width and depth of the cooking surface area in accordance with Clauses 5. 12. 1. 2 of AS 5601 However, in no case shall this clearance to any surface be less than 450mm. SIDE CLEARANCE Where the distance measured between the periphery of the burner and any vertical combustible surface is less than 200mm, the surface shall be protected in accordance with Clause 5. 12. 1. 2 of AS5601 to a height of not less than 150mm above the hotplate top surface for the full length and width of the cooking surface area. Note: the cooking surface area is defined as the part of the appliance where the cooking normally takes place and does not include those parts of the appliance containing the control knobs. INSTALLATION GAS CONNECTION 1. 5. ELECTRICAL CONNECTION • • • The electrical connections must comply with local regulations. If burners shows any abnormalties check the following: Burner cap on correctly Burner positioned correctly Burner vertically aligned with injector nipple In some cases the burners will fail to ignite immediately and will seem to 'blow's lightly when they do ignite, this is usually due to air in the gas pipe which should clear itself within seconds of operation. If after following the instructions given, satisfactory performance cannot be obtained, contact the local gas authority for advice and assistance. Please ensure the supplied data label has to be attached in a suitable surface adjacent to the hotplate such as cupboard door. WIRING DIAGRAM 00 11 22 33 44 55 66 77 88 99 09 29 49 69 90 45 N6 Q W/PI X2 : : : : BLACK BROWN RED ORANGE YELLOW GREEN BLUE VIOLET BLUE SKY WHITE WHITE-BLACK WHITE-RED WHITE-YELLOW WHITE-BLUE GREY YELLOW-GREEN SPARK IGNITION SWITCH (UNDER KNOB) SPARK IGNITION PLUG MAINS TERMINAL BLOCK/SPARK IGNITION COOKTOP EARTHING 230 - 240 V • • • The manufacturer cannot be held responsible for any injury to persons or animals or damage to property arising from failure to comply with these requirements. When the hob is installed, provide a single-pole circuit breaker with a contact separation of at least 3 mm. If necessary, the electrical power cable must be replaced exclusively with a power cable having identical characteristics to the original supplied by the manufacturer (type H05V2V2-F T90°C or H05RR-F). This operation must be performed by a qualified electrician. ASSEMBLY After having cleaned the perimeter surface, apply the supplied gasket to the hob as shown in the figure. 12. This appliance is not suitable for connection using a flexible hose. Position the hob in the worktop opening made respecting the dimensions indicated in the Product Description Sheet. Note: the power supply cable must be long enough to permit its upward extraction. ELECTRICAL CONNECTION POINT GAS CONNECTION POINT To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance with the thickness of the worktop (see figures on the right). Fig. 2 ADJUSTMENT TO DIFFERENT TYPES OF GAS If the appliance is intended to operate with a different gas from the gas type stated on the rating plate change the injectors. Use pressure regulators suitable for the gas pressure indicated in the Product Description Sheet. • The gas nozzles must be changed by After Sales Service or a qualified technician. [. . . ] • The gas cylinder (liquid gas) is not empty. • The burner openings are not clogged. Note: If the valves must be replaced, first disassemble the chain of ignition switches. It is recommended to replace the valve gaskets each time the valve is replaced, thus ensuring a perfect seal between the body and the gas train. SERVICE INSTRUCTIONS AFTER-SALES SERVICE CARE AND MAINTENANCE CLEANING THE HOB SURFACE • • Before calling the After-Sales Service, make sure you can give the following information: type of fault or problem; exact model (written on the Product Description Sheet and Warranty); service number that follows the word SERVICE on the rating plate under the hob and on the Warranty; your complete address and phone number. [. . . ]