User manual WHIRLPOOL KRSC 9010/I INSTALLATION

[. . . ] 501910200330_INST_GB_Sbs. qxp 20-11-2007 15:21 Pagina 1 KRSC 9010 KRSC 9011 Assembly instructions 501910200330_INST_GB_Sbs. qxp 20-11-2007 15:21 Pagina 2 501910200330_INST_GB_Sbs. qxp 20-11-2007 15:21 Pagina 3 Water connection Electrical connection Refrigerator levelling Installation dimensions and requirements Removing the freezer door (A) Removing the refrigerator door (B) Fitting the freezer door (C) Fitting the refrigerator door (D) Horizontal alignment of freezer and refrigerator door (E) Vertical alignment of freezer and refrigerator door (F) 4 4 5 6 7 7 8 8 9 9 501910200330_INST_GB_Sbs. qxp 20-11-2007 15:21 Pagina 4 Water connection Disconnect your refrigerator from the power supply before starting the operation. • Make sure to comply with the current local regulations regarding connection to the water system. [. . . ] • The appliance does not require adjustments or a water drain. Electrical connection Earthing of the appliance is compulsory by law. The type of current and the mains voltage to which the appliance is connected must correspond to that given on the rating plate. The connection socket must be accessible even after installation, so that the appliance can be unplugged if necessary. If this is not possible, connect the appliance to the mains by means of a two-pole switch, with contact opening distance of at least 3mm, located in an accessible place. If the power cable plug and socket are not of the same type, replace the socket. Do not pull the power cable when unplugging the appliance. 4 501910200330_INST_GB_Sbs. qxp 20-11-2007 15:21 Pagina 5 Refrigerator levelling The refrigerator has two front and two rear wheels, located on each side at the bottom of the appliance, that can be adjusted (see figure A), or four wheels, of which only the two front ones are adjustable (see figure B). If the appliance seems unsteady or you want the doors to close more easily, it is advisable to adjust the inclination of the appliance following the instructions given below (depending on the model, as shown in the figures opposite). Check the installation position in order to guarantee a space of at least 1 cm on all sides including the top. Connect the appliance to the power supply. Move the refrigerator into its final position. [. . . ] Note: Do not unscrew the levelling screws too much when lowering the appliance, otherwise they could come out. Aligning the doors: If, after switching on the appliance and adjusting the refrigerator and freezer doors, the doors are misaligned, disconnect the appliance from the power supply and adjust them as indicated in the attached diagram. Figure A Figure B 5 501910200330_INST_GB_Sbs. qxp 20-11-2007 15:21 Pagina 6 6 501910200330_INST_GB_Sbs. qxp 20-11-2007 15:21 Pagina 7 7 501910200330_INST_GB_Sbs. qxp 20-11-2007 15:21 Pagina 8 8 501910200330_INST_GB_Sbs. qxp 20-11-2007 15:21 Pagina 9 9 501910200330_INST_GB_Sbs. qxp 20-11-2007 15:21 Pagina 10 501910200330_INST_GB_Sbs. qxp 20-11-2007 15:21 Pagina 11 501910200330_INST_GB_Sbs. qxp 20-11-2007 15:21 Pagina 12 Printed in Italy 11/07 n GB 5019 102 00330 [. . . ]