User manual WHIRLPOOL WED99HEDC INSTALLATION GUIDE

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual WHIRLPOOL WED99HEDC. We hope that this WHIRLPOOL WED99HEDC user guide will be useful to you.

Lastmanuals help download the user guide WHIRLPOOL WED99HEDC.


Mode d'emploi WHIRLPOOL WED99HEDC
Download

You may also download the following manuals related to this product:

   WHIRLPOOL WED99HEDC DIMENSION GUIDE (319 ko)
   WHIRLPOOL WED99HEDC USE & CARE GUIDE (5539 ko)
   WHIRLPOOL WED99HEDC WARRANTY INFORMATION (150 ko)
   WHIRLPOOL WED99HEDC VENTILATION SPECIFICATION (1518 ko)

Manual abstract: user guide WHIRLPOOL WED99HEDCINSTALLATION GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] Com INSTALLATION NOTES Date of purchase:__________________________________ Date of installation:________________________________ Installer:_________________________________________ Model number:____________________________________ Serial number:____________________________________ NOTES CONCERNANT L’INSTALLATION Date d’achat :______________________________________ Date d’installation :_________________________________ Installateur :_______________________________________ Numéro de modèle :_________________________________ Numéro de série :___________________________________ W10678946B W10678949B - SP Dryer Safety Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel – Do not contact the thermostat bracket while the appliance is energized. IMPORTANT: When discarding or storing your old clothes dryer, remove the door. Installation Requirements TOOLS AND PARTS Gather the required tools and parts before starting installation. [. . . ] Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Screw in leveling legs SAVE THESE INSTRUCTIONS Using a wrench and tape measure, screw leveling legs into leg holes until bottom of foot is approximately 1/2" (13 mm) from bottom of dryer. Slide the dryer until it is close to its final location. € This connection may be used with either a power supply cord or a direct wire connection. Remove terminal block cover A B C D Remove the screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections (C) into the hole below the terminal block opening (B) so that one tab is pointing up (A) and the other is pointing down (D), and hold in place. Tighten strain relief screws just enough to hold the two clamp sections (C) together. Remove hold-down screw and terminal block cover. Prepare to connect neutral ground wire and neutral wire E B A Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point. If your outlet looks like this: Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to “4-Wire Power Supply Cord Connection”. Strip 5" (127 mm) of outer covering from end of cable, leaving bare ground wire at 5" (127 mm). Cut 11/2" (38 mm) from remaining 3 wires. Connect remaining wires E B A Remove center terminal block screw (B). Remove neutral ground wire (E) from green external ground conductor screw (A). Connect neutral ground wire and neutral wire B E Place hooked ends of remaining direct wire cable wires under outer terminal block screws (hooks facing right). squeeze hooked ends together and tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Prepare your 3-wire cable for direct connection 1" m) 25 m ( C Connect neutral ground wire (E) and place hooked end (hook facing right) of neutral wire (white or center wire) (C) of direct wire cable under center screw of terminal block (B). 52 m) of extra length so dryer may be moved if needed. [. . . ] Using a Phillips screwdriver, remove the 10 screws securing the inner door to the outer door. Using a T25® screwdriver, reinstall the latch plate and latch backing plate with the 3 screws removed earlier and the hinge assembly with the 5 screws on the opposite sides from which they were removed. Reinstall inner door assembly Bottom of door Hinge Using a T25® screwdriver, remove the 3 screws securing the latch plate and latch backing plate and the 5 screws holding the hinge assembly in place. Position the door with the inside of the door facing up. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WED99HEDC

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WED99HEDC will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag