User manual WHIRLPOOL WGD7000DW INSTALLATION GUIDE

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual WHIRLPOOL WGD7000DW. We hope that this WHIRLPOOL WGD7000DW user guide will be useful to you.

Lastmanuals help download the user guide WHIRLPOOL WGD7000DW.


Mode d'emploi WHIRLPOOL WGD7000DW
Download

You may also download the following manuals related to this product:

   WHIRLPOOL WGD7000DW DIMENSION GUIDE (320 ko)
   WHIRLPOOL WGD7000DW USE & CARE GUIDE (4515 ko)
   WHIRLPOOL WGD7000DW WARRANTY INFORMATION (143 ko)
   WHIRLPOOL WGD7000DW QUICK REFERENCE SHEET (851 ko)
   WHIRLPOOL WGD7000DW VENTILATION SPECIFICATION (1518 ko)

Manual abstract: user guide WHIRLPOOL WGD7000DWINSTALLATION GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] INSTALLATION NOTES Date of purchase:__________________________________ Date of installation:________________________________ Installer:_________________________________________ Model number:____________________________________ Serial number:____________________________________ NOTES CONCERNANT L’INSTALLATION Date d’achat :______________________________________ Date d’installation :_________________________________ Installateur :_______________________________________ Numéro de modèle :_________________________________ Numéro de série :___________________________________ W10680136B W10680137B-SP 1 DRYER SAFETY 2 3 INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Tools needed for gas installations: Tools needed for all installations: 8" (203 mm) or 10" (254 mm) pipe wrench Flat-blade screwdriver #2 Phillips screwdriver 8" (203 mm) or 10" (254 mm) adjustable wrench (for gas connections) Pipe-joint compound resistant to LP gas 1/4" nut driver or socket wrench (recommended) Tin snips (new vent installations) Parts supplied (all models): Tape measure Vent clamps Leveling legs (4) Parts supplied (steam models): Level Pliers “Y” connector Short inlet hose Rubber washer Parts package is located in dryer drum. Parts needed (steam models): Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench Caulking gun and compound (for installing new exhaust vent) 5' (1. 52 m) inlet hose If using a power supply cord: Utility knife Putty knife Use a UL listed power supply cord kit marked for use with clothes dryers. [. . . ] Do not further tighten strain relief screws at this point. For 3-wire Power Supply Cord Connection, see page 13. For 4 wire Power Supply Cord Connection, continue to step 3. Connect neutral ground wire (E) and neutral wire (white or center) (C) of power supply cord under center terminal block screw (B). Connect ground wire F 4-wire Power Supply Cord Connection IMPORTANT: A 4-wire connection is required for mobile A. Homes and where local codes do not permit the use of 3-wire connections. 3/4" (19 mm) UL listed strain relief G. Ring terminals Connect ground wire (F) (green or bare) of power supply cord to external ground conductor screw (A). Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Remove center screw Unscrew the removable conduit connector (A) and any screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the hole (B) below the terminal block opening. Reaching inside the terminal block opening, screw the removable conduit connector onto the strain relief threads (C). Attach direct wire cable to strain relief Remove center terminal block screw (B). The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. For 3-wire Direct Wire Connection, see page 15. For 4 wire Direct Wire Connection, continue to step 3 on the next page. Connect neutral wire (white or center) (C) of power supply cord to center terminal block screw (B). 13 4-wire Direct Wire Connection IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit 3-wire connections. Prepare your 4-wire cable for direct connection 31 ⁄2" m) (89 m 1" m) (25 m B 5 (127 " mm ) Direct wire cable must have 5 ft. 52 m) of extra length so dryer may be moved if needed. Strip 5" (127 mm) of outer covering from end of cable, leaving bare ground wire at 5" (127 mm). [. . . ] NOTE: You may notice an odor when the dryer is first heated. This odor is common when the heating element is first used. Remove bottom screws from dryer cabinet side of hinges. Loosen (do not remove) top screws from dryer cabinet side of hinges. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WGD7000DW

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WGD7000DW will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag