User manual WHIRLPOOL WGD92HEFU INSTALLATION GUIDE

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual WHIRLPOOL WGD92HEFU. We hope that this WHIRLPOOL WGD92HEFU user guide will be useful to you.

Lastmanuals help download the user guide WHIRLPOOL WGD92HEFU.


Mode d'emploi WHIRLPOOL WGD92HEFU
Download

You may also download the following manuals related to this product:

   WHIRLPOOL WGD92HEFU DIMENSION GUIDE (382 ko)
   WHIRLPOOL WGD92HEFU USE & CARE GUIDE (5851 ko)
   WHIRLPOOL WGD92HEFU WARRANTY INFORMATION (154 ko)
   WHIRLPOOL WGD92HEFU QUICK REFERENCE SHEET (1987 ko)
   WHIRLPOOL WGD92HEFU VENTILATION SPECIFICATION (1518 ko)

Manual abstract: user guide WHIRLPOOL WGD92HEFUINSTALLATION GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] Com INSTALLATION NOTES Date of purchase:___________________________________ Date of installation:_________________________________ Installer:__________________________________________ Model number:_____________________________________ Serial number:_____________________________________ NOTES CONCERNANT L’INSTALLATION Date d’achat:______________________________________ Date d’installation:__________________________________ Installateur:_______________________________________ Numéro de modéle:_________________________________ Numéro de série:___________________________________ W10775221B W10775222B-SP DRYER SAFETY 2 3 INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before starting installation. Tools needed for gas installations: Tools needed for all installations: 8" or 10" pipe wrench 8" or 10" adjustable wrench (for gas connections) Flat-blade screwdriver #2 Phillips screwdriver Pipe-joint compound resistant to LP gas ¼" and 5/16" nut driver (recommended) Level Parts supplied (all models): Tape measure Pliers Leveling legs (4) Parts supplied (steam models): Utility knife Tin snips (new vent installations) “Y” connector 2' (0. 6 m) inlet hose Caulking gun and compound (new vent installations) Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench Rubber washer Parts package is located in dryer drum. NOTE: Do not use leveling legs supplied with dryer if installing with a pedestal or a stack kit. [. . . ] ■■ Bend vent gradually to avoid kinking. –■ Use as few 90° turns as possible. Determine vent length and elbows needed for best drying performance: ■■ Use the “Vent System Charts” on the next page to determine Optional exhaust installations: This dryer can be converted to exhaust out the right side, left side (all models except long vent), or through the bottom. If you prefer, you may contact your local dealer to have the dryer converted. type of vent material and hood combinations acceptable to use. NOTE: Do not use vent runs longer than those specified in “Vent System Charts. € Exhaust systems longer than those specified will: ■■ Shorten life of dryer. –■ Reduce performance, resulting in longer drying times and increased energy usage. Bottom exhaust installation C 11 The “Vent System Charts” provide venting requirements that will help achieve best drying performance. 2 m) Vent must fit over the exhaust hood. secure vent to exhaust hood with 4" (102 mm) clamp. Run vent to dryer location using straightest path possible. Do not use duct tape, screws, or other fastening devices that extend into interior of vent to secure vent, because they can catch lint. € The dryer must be connected to the cold water faucet using the new inlet hoses (not supplied). NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates on the hoses for future reference. Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found. To determine if your model has a long vent system, refer to the type code located on the serial number plate in the inner door well.  urn cold water off, remove hose, T and replace rubber washer Install Vent System 1. (305 mm) Turn cold water faucet off and remove washer inlet hose. (305 mm) Remove old rubber washer from inlet hose and replace with new rubber washer. Install exhaust hood and use caulking compound to seal exterior wall opening around exhaust hood. [. . . ] Using a Phillips screwdriver, remove the 10 screws securing the inner door to the outer door. Remove hinge and latch Latch Using a T25® screwdriver, remove the 2 screws securing the door strike to the door frame of the dryer. Rotate the strike 180° and attach to the opposite side of dryer door frame as shown. Hinge Using a T25® screwdriver, remove the 3 screws securing the latch plate and latch backing plate and the 5 screws holding the hinge assembly in place. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WGD92HEFU

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WGD92HEFU will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag