User manual WHISPER CREEK ARCHERY COMPOUND BOW 2006

[. . . ] 2006 Compound Bow Owner's Manual Table of Contents Whisper Creek Mission Bow Terminology Safety Instructions Care Instructions Cam Performance Draw Length Adjustments Let-Off Adjustments Draw Weight Adjustments Bow Press Instructions Whisper Creek Technology 3 4 5 6 7 8 10 10 11 12 W H AT SETS US APA RT We can assure you that no other bow company has the technology that Whisper Creek Archery has. Whisper Creek Archery is light-years ahead of others when comparing to "Compound Bow" Technology. Our mission at Whisper Creek Archery is to provide you with the highest quality and most technologically advanced bow in the industry. Through extensive research and development, our technology provides the archer with the quietness, precision, speed, and versatility that are needed to perform the job well. [. . . ] A 1/2 inch of adjustment in 1/8" increments can be obtained through the full range of the string anchor post. DRAW LET-OFF ADJUSTMENTS CounterFORCEONE The let-off is adjusted by completely changing out from an 80% module to a 65% module. CounterFORCECPS&1/2 The let-off is factory set to 70% for this cam system; therefore, there are no adjustments. DRAW WEIGHT ADJUSTMENT Your bow is equipped with 10 pounds of draw weight adjustments. To simply adjust your draw weight, always bottom out your limb bolt then back out your limb bolt for the desired draw weight (WARNING: NEVER back off limb bolt more than 5 turns ­ failure of not complying could cause serious injury). BOW PRESS INSTRUCTION WARNING!!! Placing a Whisper Creek Bow into a bow press improperly will result in damage to the bow. ALWAYS make sure that when servicing a Whisper Creek Bow that the bow is placed EXACTLY per manufacturing's instructions. Extension arms are needed to work on the Whisper II Risers (Innovator, Spectrum, Odyssey, InnovatorPRO, etc. ) ­ these extension arms can be obtained through Whisper Creek Archery. It is imperative that the rollers are moved on the limb located at the pocket to ensure no product damage. P1 Actuator or Strut P2 R1 R2 Hydraulic Piston (Parallel Limb Bow Presses ONLY) ­ sight window is to always be on opposite side to the hydraulic piston. NOTE: NEVER USE A CENTER PULL BOW PRESS (A BOW PRESS THAT ANCHORS AT THE GRIP AREA OF THE BOW). The BowDAMPTM was designed to work in conjunction with the cams and wheels for a serious shock and noise damping system. This type of damping system is the most advanced of its kind. With our patent pending BowDAMPTM Technology, also known as Constraint or Extensional Layer Damping, each shot is damped by not allowing vibration and noise to travel to adjacent members, thus killing vibrations and noise dead in its track!"BowDAMPTM TECHNOLOGY SYSTEMS PROVIDE WEIGHTEFFICIENT, HIGH-LEVEL DAMPING" · BowDAMPTM is a patent pending Constraint or Extensional-LayerDamping (CELD) application where it utilizes a multi-layer "sandwich" system that is formed by laminating the base layer to a damping layer and then adding a third constraining layer (Figure 1). Typically, the constraining layer is of the same material as the base layer, but exceptions are common. · In this sandwiched construction, the damping material layer is forced into a shape that shears adjacent material sections when the system flexes during vibrations. This alternating shear strain in the CELD material dissipates the vibration as low-grade frictional heat (Figure 2). · BowDAMPTM is Structural damping where structural damping (constraint layer) is to structural vibration what absorption is to airborne sound. That is, it provides a means for eliminating mechanical energy by converting it to heat. Damping materials are often applied directly to the surface of a structure using adhesive. B OW DA M PT M & BOWSUSPENSIONT M M ATERIAL TECHNOLO G Y What a technology breakthrough!Talking about endurance, reliability, strength, infinite wear life, enormous damping characteristics, and acoustical properties - all rolled up into one complete bow system. This bow system was designed with only one thing in mind - serious "DAMPING". The BowDAMPTM Material is excellent for low to high impact with repetitive pounding such as the use with compound bows!The BowDAMPTM Material will not swell or deteriorate in water where most plastics and/or elastomers will. BowDAMPTM Material Technology was designed to resist high impact as well as having "outstanding" abrasive resistance. Its abrasive resistance is about 20 times better than that of steel - that's right steel!It is also known for its toughness and durability. Its compression characteristics are better than any mechanical coil springs and it is designed to return to its original shape shot after shot!The BowDAMPTM Material is superior to other elastomers on almost all accounts. Other elastomers will generally fail under repeated flexing due to the development and propagation of cracks. [. . . ] It is also designed to be in free state to counter-react the harmonics within the limbs; thus, disrupting the entire bow's harmonics and resulting in a huge noise reduction. Question: Can I shoot a lower grains/pound arrow with this technology?This technology is actually more efficient as the draw weight increases and/or arrow weight decreases. Question: Does this technology affect accuracy or repeatability? [. . . ]