User manual WHISTLER 3300SWRA

[. . . ] Nut #10-32 · Use with #10-32 bolts. Lock Washer · Use with #10-32 bolts. Flat Washer · Use with #10-32 bolts. Sheetmetal Screw #6 x 3/4" · Fastens Large L/Small L Bracket or 45º Reflector to radar antenna. [. . . ] You may also use 2 #6 sheet metal screws. Because rough road surfaces can cause excessive vibration or bouncing, be certain to fasten the bracket(s) securely to your vehicle. Horizontal Or Vertical Mounting Of Antenna The antenna can be attached to the vehicle in a horizontal or vertical position, or at any angle between these two points. Select the position that allows you to fasten the antenna to your vehicle in the most secure manner. Radar antenna mounted in horizontal position. Horizontal Mounting When mounting the antenna in a horizontal position (or on an angle between), remember to keep the ANTENNA window as close to perpendicular as possible to the road surface (ANTENNA window should not be angled up toward the sky or down toward the road surface). Mounting Vertical (with 45º Reflector) For vehicles that do not have sufficient clearance behind the bumper (about 5") to mount the antenna in a horizontal position, the 45º Reflector should be used. The 45º Reflector is attached to the antenna with two screws (#6 x 3/4") on the side of the antenna housing marked ANTENNA. Slide the screws through the corner holes on the flange of the antenna housing and then tighten into the metal reflector (do not over tighten). 8 9 3300 Superwideband remote 10/4/00 9:38 AM Page 13 INSTALLATION OF RADAR ANTENNA Mount the antenna to the vehicle such that the ANTENNA window is facing the road surface, sky, right or left of the vehicle, and the reflector has an unobstructed view of the road ahead. This side facing rearward traffic Antenna window Signal MAKING THE CONNECTION Antenna Cable To Control Panel Once the antenna is installed, run the cable along the inside of the vehicle or under it to the engine compartment. If using the latter, find a location in the firewall where other wires (or the speedometer cable) enter the passenger compartment and feed the stereo jack connection through. Be careful not to interfere with or disconnect other wires, cables, or mechanical systems of your vehicle while routing the antenna cable. Also, keep the antenna cable away from any areas in the vehicle that may become hot. Four cable ties are provided to secure the antenna cable at various points on the vehicle. Engaging SWRA To engage the rear radar antenna: 1. Unplug power cable from the console or turn vehicle off if console is wired to a switched 12 volt source. Plug the stereo jack connector (straight ended cable) at the end of the rear antenna cable into the RADAR 2 port on the back of the control panel. Display reads: Radar antenna mounted(vertical) with 45º Reflector. Mounted in this position, radar signals are reflected into the ANTENNA window. R2 ON? Press Dark for Yes or City for No. When radar is received from the rear the display reads: K* 10 11 9 3300 Superwideband remote 10/4/00 9:38 AM Page 15 TROUBLESHOOTING GUIDE Memory For Feature Selected Your preference for feature settings is maintained even when the unit is unplugged. If power to the Whistler is removed, the user selectable features are retained in memory. The SWRA-3300 is expertly engineered and designed to exacting quality standards to provide you with reliable, trouble-free operation. If your unit has been correctly installed following the guidelines in this manual, but is not operating optimally, please refer to the troubleshooting guide below. · Check fuse in power cable, replace if necessary. · Check fuse in fuse box, replace if necessary. · Make sure power cable is properly grounded. · Warning communicates "loss of link" between control panel and front antenna (RADAR 1). [. . . ] Ship the unit in the original carton or in a suitable sturdy equivalent, fully insured, with return receipt requested, and shipping charges prepaid to: Whistler Repair Dept. Rogers AR 72756 WARRANTY IMPORTANT: Whistler will not assume responsibility for loss or damage incurred in shipping. Therefore, please ship your unit insured with return receipt requested. Include with your unit the following information, clearly printed: · Your name and street address (for shipping via UPS), and a daytime telephone number. [. . . ]