User manual WHISTLER FUZION INSTALLATION

[. . . ] Mounting Cable Tie · Secures cable from radar antenna at various locations in engine compartment. 4" Cable Tie · Secures cable from radar antenna at various locations in or under the vehicle. Interface Cable · Connects the radar antenna to inside control panel Nut 5mm · Used with studs on control panel Lock Washer 5mm · Used with studs on control panel Qty 2 B 2 C 4 4 2 7 C Nut 4mm D Lock Washer 4mm E Flat Washer D E F Sheet metal Screw #6 x 3/4" G Sheet metal Screw #4 x 5/8" F G 2 H 1 H Hook and Loop Fastener I I 1 Mountable Cable Tie J 5 K 1 J 4" Cable Tie K L 2 M 2 Interface Cable L Nut 5mm M Lock Washer 5mm Note: If mounting fasteners are missing from your package, please call 1-800-531-0004 for replacements. 5 6 INSTALLATION OF RADAR ANTENNA General Information The radar antenna is waterproof and designed to be mounted at the front of your vehicle. In most vehicles the best mounting location is directly below or behind the bumper. [. . . ] The 45º Reflector is attached to the antenna with two screws (#6 x 3/4") on the side of the antenna housing marked ANTENNA. Slide the screws through the corner holes on the flange of the antenna housing and then tighten into the metal reflector (do not over tighten). 9 10 INSTALLATION OF RADAR ANTENNA Mount the antenna to the vehicle such that the ANTENNA window is facing the road surface, sky, right or left of the vehicle, and the reflector has an unobstructed view of the road ahead. INST ALLA TION OF LASER ANTENNA Antenna Cable to the Control Panel Once the antenna is installed connect the cable from the radar antenna to quick disconnect interface cable. Tie this cable in knot similar to using an electrical extension cord. Run the cable along the edge of the engine compartment to the firewall. Find a location in the firewall where other wires (or the speedometer cable) enter the passenger compartment and feed the stereo jack connection through. Be careful not to interfere with or disconnect other wires, cables, or mechanical systems of your vehicle while routing the antenna cable. Also, keep the antenna cable away from any areas in the engine compartment that may become hot. Cable ties are provided to secure the antenna and Temperature Probe cables at various points in the engine compartment. General Laser Information The laser antenna provides both front and rear laser reception. Mount the laser antenna with the 3-lens array facing forward (down the road) and the single lens facing behind. This approach offers the greatest protection, since you will most often be traveling into a laser signal, rather that away from it when laser speed enforcement is encountered. For effective protection, make sure the laser antenna has an unobstructed view forward and behind, and that it is not placed behind metallic sun screens. Mounting the Laser Antenna The laser antenna can be mounted to the front windshield using the windshield bracket supplied. Mounted in this position, radar signals are reflected into the ANTENNA window. Mounting the Temperature Probe Find a location that is far enough away from the engine and radiator heat but still in the airflow for the vehicle. Mounting the Probe too close to these heat areas will give a false high temperature. · Attach the mountable tie wrap (supplied) to the Temperature Probe as shown. · Mark location for Probe, then drill a hole using a 7/64" drill bit. Attach Probe with tie wrap in the correct orientation using the #6 x 3/4 screws. NOTE: Mount the Probe so that there is space between the Probe and the mounting area. Do not mount Probe directly to metal area. 11 12 INST ALLA TION OF LASERANTENNA Installing the Laser Antenna Before using, attach the suction cup and rubber bumpers (2) to the metal bracket. If necessary, you may bend the metal bracket in order to position the laser antenna correctly (3-lens array facing forward, single lens facing behind. ) INST ALLA TION OF CONTROLPANEL The Fuzion remote is designed to fit into standard 2 1/16" gauge housings. This unit is perfect to complement other gauges in a pillar pod or install in its own gauge housing. [. . . ] Antenna Port 15 16 INST ALLA TION OF VOICE MODULE The Voice Module provides not only remote audio but voice announcements as well. To install: · Make sure the external speaker option is turned on (factory) default setting is voice on, if not see option mode in owners manual · For maximum volume, find a convenient location close to the driver's ear, such as the trim panel between A & B pillars. Attach speaker using the supplied clip or velcro. · Plug the cable into the aux cable on the detector. [. . . ]