User manual X10 IR10A

[. . . ] IconRemote TM Owner's Manual Model IR10A Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hard Key Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Does it operate the target device? You can learn commands from an existing remote and store them under the "Main" keys on the IR10A remote, or learn commands from an existing remote and store them under any of the 10 Side Keys. At the Home screen press the Side Key next to Learn. At this screen you press any of the 5 Side Keys K1-K5 on the left to learn commands under a Side Key, or press any of the top 4 Side Keys K6-K9 on the right to learn commands under the main keys on the remote. If you press a right Side Key (to select Main Keys) you are going to learn, say, the Chan Up key from an existing remote and store it under the Chan Up key on the IR10A remote. Or learn the Power key from an existing remote and store it under the Power key on the IR10A remote, etc. If you press a left Side Key (to select Side Keys) you are going to learn, say, the "DVD Zoom" function from an existing remote and store it under a Side Key on the IR10A remote. You will then be able to name the key "DVD Zoom" and access this "DVD Zoom" function from the Mode screen when the remote is in the mode that you selected when you learned this "DVD Zoom" command. 17 16 Learning Main Keys At the Home screen press the Side Key next to Learn. Learning Main Keys, cont. You then press and hold (in this example) the Power key on the other remote, until the display shows that the command has been successfully learned. Note for some types of key you might need to hold the key pressed, but for other types a quick press is sufficient. If keys you learn are sent multiple times try learning them with just a quick press. If the screen says Failure, you can press the key and try again. You can continue learning more individual keys by following the instructions on the screen, and then press Done when you're finished. Or you can press Add Key to Macro, (see below and next page). Then press one of the top 4 Side Keys K6-K9 to the right of the screen. Select the Device you want to learn keys for. In this example we only have a TV, Cable Box and Satellite Receiver set up, so the rest are grayed out, but you can still select any of the devices to learn commands for. You are then instructed to line up the remotes, and press the key on the IR10A remote that you want to learn. Learning a Macro - Main Keys At this screen you can select Add Key to a Macro. Then instead of learning another "separate" key, the next key you learn will be added to a Macro. This Macro will be activated by the key that you learned the first command under. E. G. , you could press Power and learn the power command from your TV's remote, then select Add Key to Macro, and press the 3 key and learn the channel 3 key from your TV's remote. Then the Macro stored under the Power key will turn on the TV and change the channel to number 3. You then point the remote you want to learn commands from at the bottom of the IR10A remote, and press the key on the IR10A remote that you want to learn a command under, e. g. , the Power key. 18 19 Macros - Main Keys, cont. Before learning the second key in the Macro, you can if desired, set a delay (1-10 secs) after which the command stored in the Macro will be sent. For example your TV might require a few seconds after turning it on before it will respond to a Channel Up/Down command. (Repeatedly press the Side Key next to Set Delay, or enter the delay directly with the numeric keys, 0-9). In this case let's set a 1 second delay between commands. Then point your existing remote at the bottom of the IR10A remote and press OK when you're ready. Learning Side Keys At the Home screen press the Side Key next to Learn. Then press any of the Side Keys K1K5 to the left of the screen. You then press the second key on your original remote that you want to add to the Macro. Select the device you want to learn keys for. In this example we only have a TV, Cable Box and Satellite Receiver set up, so the rest are grayed out, but you can still select any of the devices to learn commands for. [. . . ] Then in AUX mode (for example) press a number button on the iconRemote corresponding to the X10 Module you want to control, then press CHANNEL + to turn the module on, CHANNEL ­ to turn it off, VOLUME + to brighten Lamp and Wall Switch Modules, and VOLUME ­ to dim them. You can also press the POWER button to turn on ALL lights connected to Lamp and Wall Switch Modules and press MUTE to turn off all your X10 modules (including Appliance Modules). Troubleshooting, cont. Having problems with learning?· If some learned keys transmit multiple times, e. g. if a learned Channel Up key changes more than one channel when you press it, or Up/Down/Left/Right navigation keys move more than one step when you press the learned key; try just giving the key to be learned a quick press (when you learn it) rather than holding the key pressed until the screen displays Success. [. . . ]