User manual X10 WS14A

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual X10 WS14A. We hope that this X10 WS14A user guide will be useful to you.

Lastmanuals help download the user guide X10 WS14A.


Mode d'emploi X10 WS14A
Download
Manual abstract: user guide X10 WS14A

Detailed instructions for use are in the User's Guide.

[. . . ] Single & 3-Way Decorator Wall Dimmer Set Up and Operating Instructions WS12A/WS14A Traveller wires Cap off with wire nut A WS12A B WS12A Master WS14A Companion The WS12A Wall Dimmer Module is designed to control incandescent loads with a rating of between 40W and 500W. Lamps rated below 40W may flicker or operate erratically. The switch can replace a single switch that controls a ceiling light or outside light. [. . . ] Make sure no bare whiskers of wire are protruding, use insulating tape to cover wire nuts if necessary. Installing the Wall Dimmer Module (3-way applications, diagram B) · Disconnect the power at the circuit breaker panel. · Remove wall plates and unscrew the existing switches from their boxes. Identify the common wire at each existing switch (usually connected to a different color terminal). · Replace one of the existing wall switches with the WS12A Wall Dimmer (Master): connect the common wire to the blue wire on the WS12A using a wire nut. Connect the two remaining "traveller wires" to the red and black wires on the WS12A, using wire nuts. If one of the travellers is red connect it to the red wire on the WS12A. · Replace the other existing wall switch with the WS14A Companion Switch (sold separately): connect the common wire to one of the WS14A's terminals labelled LIVE. Connect the traveller which you connected to the red wire on the WS12A to the terminal labelled SWITCH on the WS14A. Connect the remaining traveller wire to the second terminal labelled LIVE on the WS14A. Screw both switches into their wall boxes. Setting up and operating the Wall Dimmer Module · Pop the rocker paddle off the WS12A (using a small screwdriver). Set the House Code dial to the same letter (A thru P) that you set on your X10 controller(s). · Set the Unit Code dial to an unused code (1 - 16) which can be controlled from any X10 controller. · Set the power on-off slide switch (under the rocker paddle) to the ON (right) position. Turn this switch OFF (left) when changing a light bulb. [. . . ] X10 agrees to repair or replace, at it's sole discretion, a defective X10 product if returned to X10 within the warranty period and with proof of purchase. If service is required under this warranty: Call 1-800-442-5065, visit www. x10. com, or e-mail sales@x10. com. X10. com, a division of X10 Wireless Technology, Inc. http://www. x10. com/support WS12A -10/02 [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE X10 WS14A

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual X10 WS14A will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag