User manual XEROX 1010 ST MAC OS X INSTALLATION/CONFIGURATION INSTRUCTIONS

[. . . ] Other company trademarks are also acknowledged. PCL is a trademark of the Hewlett Packard Company. This printer contains an emulation of the Hewlett Packard PCL 5 command language, recognized HP PCL 5 commands, and processes these commands in a manner compatible with Hewlett Packard Laserjet printer products. PostScript is a registered trademark of Adobe Systems, Inc. [. . . ] Enter a menu option number to toggle through the available settings. When the desired settings for all options are reached, apply the settings to the printer using the " a " option in the menu. 11-2 XPrint UNIX SYSTEM PRINTER DRIVER INSTALLATION 12 Removing a XPrint printer. Overview: Run the setup49XX configuration utility to remove a XPrint 49XX printer configuration from your workstation or remote print spooler. Setup: NOTE: The following instructions assume you have correctly completed the XPrint 49XX PostScript Print Tool installation. You will need to know the complete path to the installation directory or have added it to your search path to continue. Run the 49XX printer setup utility: TYPE: /bin/setup49XX [ENTER] NOTE: 49XX is model number for the printer model you are installing. For example, if you are installing XPrint 4920, then the setup command would be setup4920. From the Setup XPrint49XX menu, select option 2. TYPE: 2 [ENTER] XPrint UNIX SYSTEM PRINTER DRIVER INSTALLATION 12-3 13 Administration Overview: TCP/IP and lpr on the 49XX can be administrated in a number of different ways: Telnet PC XPrint Printer Services MAC XPrint Printer Services 49XX Control panel It is up to you and your environment to decide which administration utility best fits your needs. 13-4 XPrint UNIX SYSTEM PRINTER DRIVER INSTALLATION 4915/4920/4925 Printer Parameters Configurable via Telnet The 49XX printer allows MOST of its Network Card (NIC) parameters to be viewed and set using Telnet. The 49XX printer NIC can also be remotely reset or initialized using Telnet. The following is a summary of Telnet configurable NIC parameters: Protocol Settings TCP/IP: ip address (can be hard coded: xxx. xxx. xxx. xxx) ip security (can be set up by ip address and even by ip subnet #'s) LPD ("Line Printer Daemon" enabled/disabled) LPR Banner Pages (yes/no -- Enable / Disables LPR banner pages) IPX: Netware (Enables / Disables IPX Pserver) Ethernet Type (IPX packet frametype settings) Primary Netware Server (NetWare server storing 49xx queue and pserver information) Netware Printer Name (name NIC uses to advertise itself and attach to Netware queues) Queue Scan Rate (time interval that 49XX waits before it polls it queue(s) for print jobs. ) AppleTalk: EtherTalk (enabled/disabled) NetBeui: Netbeui Group (workgroup printer displays itself in) Netbeui Name (name printer displays itself as) Service Name (name advertised on Microsoft NETBEUI network) Service Description (text description of printer) Service Password (password used on Microsoft NETBEUI network) XPrint UNIX SYSTEM PRINTER DRIVER INSTALLATION 13-5 NIC Settings Ethernet: Connector Type (bnc, rj45, autoselect) TokenRing: Connector Type (db9, rj45, autoselect) Ring Speed (4mbs, 16mbs) Routing (yes/no -- source routing: enabled/disabled) Card Address (TokenRing physical address can be set) Reset Printer (yes/no -- resets NIC and enables any NIC changes) Reset network card settings to factory defaults (yes/no -- resets NIC to default settings) Read Only Settings The following is a list of displayable NIC parameters (Read Only) NIC Firmware Revision (NICs firmware revision) Processor Speed (NIC processor speed) Ethernet Address (physical layer address) 13-6 XPrint UNIX SYSTEM PRINTER DRIVER INSTALLATION To Use Telnet: At any Telnet client (UNIX, WFW3. 11, NT, DOS, . . . ) Telnet to port 2002 of the 49XX. NOTE: Telnet will work only if the TCP/IP protocol stack is loaded AND it supports Telnet. NOTE: In the following examples, the expression XXX. XXX. XXX. XXX refers to the IP address of your XPrint printer. SeeAppendix A to obtain PRINT SETTINGS page for review of your printer's IP address. You may also have a network problem. XPrint UNIX SYSTEM PRINTER DRIVER INSTALLATION 14-1 4. If you suspect that the cause of the communications problem is the 49XX printer, print out a Printer Setting page at the 49XX control panel and view the 49XX TCP/IP parameters. Try "hard coding" the 49XX IP address at the control panel. Reset the printer, and check for connectivity again with the ping command. Verify the following settings on thePrinter Settings page with your local TCP/IP address administrator. This person should be able to verify the correctness of the settings: IP address Subnet Mask Default Gateway NOTE: Any one of these important TCP/IP parameters (if set incorrectly) can cause TCP/IP communication problems. NOTE: Subnet Mask and Default Gateway are critical on multi network segment LAN/WAN's. NOTE: If you make any TCP/IP configuration changes, then the 49XX printer must be reset for those changes to take effect. If all of the above troubleshooting fails, you may have a malfunctioning NIC. Try a Factory Reset at the 49XX control panel. Hard code IP address, Subnet mask, and default Gateway at the 49XX printer. [. . . ] The Next button wraps around the display without setting the value if an error is made. After the complete IPaddress is displayed correctly, pressEnter. Reset Printer to have the new settings take effect. 15-4 XPrint UNIX SYSTEM PRINTER DRIVER INSTALLATION Appendix E Setting DEFAULT GATEWAY at the Control Panel 1. Press On Line button on the Control Panel Be sure the light next to it is OFF . [. . . ]