User manual XEROX PHASER 6350

[. . . ] Phaser® 6300/6350 color laser printer User Guide Guida dell'utente Guide d'utilisation Guía del usuario Guia do Usuário Benutzerhandbuch Gebruikershandleiding Användarhandbok www. xerox. com/office/support Copyright © 2005 Xerox Corporation. Unpublished rights reserved under the copyright laws of the United States. Contents of this publication may not be reproduced in any form without permission of Xerox Corporation. Copyright protection claimed includes all forms of matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted, including without limitation, material generated from the software programs which are displayed on the screen such as styles, templates, icons, screen displays, looks, etc. [. . . ] In the printer driver, select either Transparency as the paper type or Tray 1 (MPT) as the paper source. Phaser® 6300/6350 Color Laser Printer 3-24 Printing on Specialty Media Printing Transparencies from Trays 2­5 1. Pull the tray out of the printer. 6300-035 2. If necessary, open the paper guides: Squeeze the green tab on the length guide, and then slide it back. Slide the green side guides outward. 6300-001 3. Fan the transparencies to release sheets that are stuck together. 6300-050 Phaser® 6300/6350 Color Laser Printer 3-25 Printing on Specialty Media 4. Insert the transparencies into the tray. Caution: Do not load transparencies above the fill line indicated on the paper tray. In the following illustration, 2 indicates the maximum fill line for transparencies, labels, glossy paper, and thin card stock. MAX 1 2 MAX 6300-059 5. If necessary, press the guides inward to fit the transparencies. 6300-109 6. Insert the tray into the tray slot, and push the tray completely into the printer. 6300-110 Phaser® 6300/6350 Color Laser Printer 3-26 Printing on Specialty Media 7. On the control panel, select the transparency type: a. Select Change setup, and then press the OK button. Select Transparency, and then press the OK button. In the printer driver, select either Transparency as the paper type or the appropriate tray as the paper source. Printing Envelopes Envelopes can be printed only from Tray 1 (MPT). See also: Supported Paper Sizes and Weights for Tray 1 (MPT) on page 3-6 Envelopes Guidelines Use only paper envelopes specified in the Supported Paper Sizes and Weights table. Successful envelope printing is highly dependent on the quality and construction of the envelopes. Use envelopes made specifically for laser printers. It is recommended that you maintain constant temperatures and relative humidity. Store unused envelopes in their packaging to avoid the effects of moisture and dryness which can affect print quality and cause wrinkling. Excessive moisture can cause the envelopes to seal before or during printing. Avoid padded envelopes; purchase envelopes that lie flat on a surface. Remove air bubbles from the envelopes before loading by setting a heavy book on top of the envelopes. [. . . ] Your attention to the following safety guidelines helps to ensure the continued, safe operation of your printer. Printer Location Place the printer in a dust-free area within a temperature range of 41° F to 90° F (5° C to 32° C) and a relative humidity range of 15 percent to 85 percent. Printer Clearance Place the printer in an area where there is adequate space for ventilation, operation, and servicing. The recommended minimal spacing is: Overhead Clearance: 350 mm (14 in. ) above the printer Total Height Requirements: Printer: 457 mm (18. 3 in. ) Add 130 mm (5. 2 in. ) for the 550-Sheet Feeder. Add 341 mm (13. 6 in. ) for the 1100-Sheet High-Capacity Feeder. Other Clearances: 100 mm (4 in. ) behind the printer 600 mm (24 in. ) in front of the printer 100 mm (4 in. ) on the left side of the printer 100 mm (4 in. ) on the right side of the printer Operational Guidelines Do not block or cover the slots and openings on the printer. The printer may overheat without adequate ventilation. [. . . ]