User manual XEROX PHASER 1235

[. . . ] P H A S E R® 1 2 3 5 COLOR PRINTER User Guide Phaser® 1235 Color Printer User Guide 071-0730-00 June 2000 Copyright © Xerox Corporation. Unpublished rights reserved under the copyright laws of the United States. Contents of this publication may not be reproduced in any form without permission of Xerox Corporation. Phaser®, PhaserShare®, ColorStix®, the TekColor® icon, Made For Each Other®, DocuPrint®, WorkSet®, Ethernet®, the stylized X, and XEROX® are registered trademarks of Xerox Corporation. [. . . ] index) Light Card Stock 90 - 120 g/m2 (24-32 lb. bond) Card Stock 121 - 203 g/m2 (45-75 lb. cover) Glossy Coated Paper 121 - 160 g/m2 (82-108 lb. book) 50 sheets 10 envelopes Multi-Sheet Bypass Feeder 121 - 203 g/m2 (74-125 lb. tag) Xerox Phaser Color Laser Labels Envelopes (Monarch, #10, C5, DL, JIS B5) s For information on loading transparencies, refer to the instructions shipped in the Xerox Phaser 35 Series Transparency Film box. Use Xerox Phaser 35 Series Transparencies only. When sending a Manual Feed job to the MBF, all media must be removed and replaced each time so that the MBF registers paper for the current print job. s 26 Phaser 1235 Color Printer s When sending a Multi-Sheet Bypass Feeder (MBF) job from the driver, the printer prompts you to load the correct media if the media does not match what you previously loaded. If a different media size is loaded in the MBF than what is selected in the driver, the printer stops and the front panel prompts you to load the correct media size in the MBF. s Loading the Multi-Sheet Bypass Feeder (MBF) 1. Open the Multi-Sheet Bypass Feeder tray and unfold the single extension (a). Open the Face-up output bin at the rear of the printer and swing out the two extensions where the media will exit (b). a b Multi-Sheet Bypass Feeder 0730-30 s The Multi-Sheet Bypass Feeder (MBF) does not automatically detect paper size. Automatic 2-Sided Printing is not available with the Multi-Sheet Bypass Feeder. For Xerox Phaser 35 Series Transparencies, refer to page 30. For Xerox Phaser Color Laser Labels, refer to page 34. s 3. Insert the media and adjust the guide for the media width: s s User Guide 27 s For envelopes, refer to page 34. 0730-23 4. Set the front panel to match the media type loaded in the MBF. From the front panel, press the Menu buttons to scroll to Tray Menu. Press the Item buttons to scroll to MBF Type. The Value buttons give you these options: Media Types Media Types Plain Preprinted Letterhead Transparency Prepunched Labels 60-90 g/m2 (16-24 lb. cover) 90-120 g/m2 (24-32 lb. bond) Weight 60-90 g/m2 (16-24 lb. bond) Multi-Sheet Bypass Feeder Bond Recycled Color Card Stock Light Card Stock Envelope 28 Phaser 1235 Color Printer Media Types (Continued) Media Types Glossy Postcard Weight 121 - 160 g/m2 (82-108 lb. cover) c. Select the appropriate media type and press Enter to save your selection. See Supported page sizes and print area on page 18. Scroll with the Value buttons to select the appropriate size. Press the Enter button to save your selection. Press the On-line button to exit the Menu System. [. . . ] UNUSUAL FIRE OR EXPLOSION HAZARDS: Isopropyl alcohol may release vapors which may ignite at or above flash point. NFPA RATING: HEALTH (1) FLAMMABILITY (3) REACTIVITY (0) Formulation is classified as an OSHA Class IB Flammable Liquid 62 Phaser 1235 Color Printer NA = Not Available SECTION 6 ­ ACCIDENTAL RELEASE MEASURES Since the isopropyl-alcohol solution is completely absorbed by the applicator and the amount of isopropyl alcohol per applicator is small, the chance of a significant spill occurring is small. In the event however, that a significant amount of liquid is released, ventilate the area, especially low areas where vapors may collect, and remove all sources of ignition. Cleanup personnel need protection against liquid contact and vapor inhalation. [. . . ]