User manual XEROX PHASER 540

[. . . ] Phaser 540 Plus Color Printer The Phaser® 540 Plus Color Printer is Tektronix' second generation color laser printer. This addendum provides an overview of the new features available in the 540 Plus and the changes that apply to the Phaser 540 User Manual. The Phaser 540 Plus provides all the features, print modes, and color matching capabilities of the Phaser 540, and uses the same convenient customer replaceable components. New features in the Phaser 540 Plus include: s s s s Legal-size printing capability Faster throughput New print-quality mode Improved troubleshooting tools User Manual Addendum 1 Phaser 540 Plus Color Printer Legal-size printing The Phaser 540 Plus supports a new paper tray that accommodates legal-size paper. [. . . ] Insert the new filter. 9008-37 User Manual 4-9 4 Caring for Your Printer Insert the new imaging unit 1. 2. Turn the two small blue knobs clockwise to align the triangles. Remove the protective plastic sheet. 1 1 2 LO CK 3. 7. Insert the new imaging unit into the printer, holding it by the blue handles. Release the left handle and slide the unit in until it stops. Turn the large blue knob clockwise to insert the imaging unit completely and to lock it. When properly installed, the lock icon aligns with the black triangle. Close the front door and turn the power on. 4 3 4-10 Phaser 540 Color Printer LO CK LO CK 9008-38 5 LO CK LO CK 6 9008-39 Caring for Your Printer 4 Reset the copy count To reset the copy count for the imaging unit (and the corona wire, which is included with the new imaging unit), complete these steps. Ready Menu Exit 9008-20 1. Press the Menu button to enter the front panel menu. You will see this message in the display: Help Pages <-----> Menu 2. Press the right arrow button (--->until the display reads ) System Counts <-----> Menu 3. 4. Press the Menu button to enter the System Counts menu. Press the right arrow button (--->until the display reads ) Imaging Unit <-----> Menu 5. 6. Press the Menu button; then press the Resetbutton. Press the right arrow button (--->until the display reads ) Corona Wire <-----> Menu 7. 8. Press the Menu button; then press the Resetbutton. Press the Exit button until the display reads Ready. User Manual 4-11 4 Caring for Your Printer What to do with the used imaging unit Once you determine that the new imaging unit takes care of whatever print quality symptom you observed, dispose of the used imaging unit as normal office waste. If the new imaging unit did not take care of the symptom, put the original unit back into the printer and repack the new unit so that it is protected from any exposure to light, and save it for future use as needed. 4-12 Phaser 540 Color Printer Caring for Your Printer 4 Replacing the fuser Replace the fuser when the front panel reads Fuser: replace. Refer to "Troubleshooting and print quality quick reference" on page 6-8 for more information on diagnosing print quality symptoms. Remove the used fuser 1. Open the front door and the right side door. 9008-30 User Manual 4-13 4 Caring for Your Printer 3. 5. To unlock the fuser, turn the small blue screw that is above the large knob counterclockwise (about four turns) until it is loose. Holding the blue tab on the right, pull the fuser until the safety catch stops it. Press the blue tab on the left to release the safety catch. Be careful not to touch the areas marked with this caution icon: The fuser weighs about 4. 1 kg (9 lbs. ); take care to handle the fuser as shown in the illustrations. Caution 6. Slide the fuser out all the way, and dispose of it as normal office waste. 3 4 5 6 9008-31 4-14 Phaser 540 Color Printer Caring for Your Printer 4 Insert the new fuser 1. [. . . ] Box 500 Chemical Documentation Mail stop 55-769 Beaverton, Oregon 97077 Printer information: 1-800-835-6100 MSDS information: (503) 627-7255 User Manual D-7 D Regulatory Information MSDS for silicone oil Section I ­ Product identification Trade name and Tektronix part number: Silicone Fluid 006-7959-00 Product use: Used in Tektronix Phaser 540 color printers. Section II ­ Information on ingredients Ingredients Polydimethylsiloxane Hazardous Ingredients: None. This is not a hazardous material as defined by the OSHA Hazard Communication Standard. Section III ­ Hazards identification Potential Health Effects: Eyes: Direct contact may cause temporary discomfort. Skin: A prolonged exposure may cause slight irritation. Inhalation: Not an irritant to respiratory passages. [. . . ]