User manual XINDAK DAC-8

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual XINDAK DAC-8. We hope that this XINDAK DAC-8 user guide will be useful to you.

Lastmanuals help download the user guide XINDAK DAC-8.


Mode d'emploi XINDAK DAC-8
Download
Manual abstract: user guide XINDAK DAC-8

Detailed instructions for use are in the User's Guide.

[. . . ] 40 mm Positioning  Keep all packaging materials out of the reach of children. it may present a choking or suffocation hazard (see Precautions and tips).  The appliance must be installed by a qualified professional in accordance with the instructions provided. Incorrect installation may damage property or cause harm to people or animals. [. . . ]  A few seconds after the hob is connected to the Switching off the cooking zones • Press the button: the power of the cooking zone will progressively decrease until it is switched off. And buttons may be • Alternatively, the pressed simultaneously. This immediately returns the power setting to 0 and the cooking zone switches off. gB electricity supply , a buzzer will sound. Switching on the hob To switch the hob on, press and hold the for approximately one second. Button Programming the cooking time  All the cooking zones may be programmed for a length of time between 1 and 99 minutes. Select the cooking zone using the corresponding selector button. Set the cooking time using the “-” and “+” buttons. Confirm by pressing the The timer begins counting down immediately. A buzzer sounds for approximately 1 minute and the cooking zone switches off when the set programme has finished. Repeat the above procedure for each hotplate you wish to programme. Residual heat indicators While the temperature of the cooking zone remains above 60°C, even after the programme has finished, the residual heat indicators placed near the relevant cooking zone remain lit to prevent the risk of burns. Overheating protection If the electronic elements overheat, the hob switches off automatically and “—” appears on the display. When the temperature has reached an appropriate level, this message disappears and the hob may be used again. Safety switch The appliance has a safety switch that automatically switches off the cooking zones when they have been in operation for a certain amount of time at a given power level. When the safety switch has been triggered, the display shows “0”. For example: the right rear hotplate is set to 5 and will switch off after 4 hours of continuous operation, while the front left hotplate is set to 2 and will switch off after 6 hours. * Cast iron Enamelled steel Special stainless steel Copper, Aluminium, Glass, Earthenware, Ceramic, non magnetic Stainless steel In addition, to obtain the best results from your hob: • Use pans with a thick, flat base to fully utilise the cooking zone. • Always use pans with a diameter that is large enough to cover the hotplate fully, in order to use all the available heat. • Make sure that the base of the cookware is always dry and clean, to fully utilise and extend the life of both the cooking zones and cookware. • Avoid using the same cookware that has been used on gas burners: the heat concentration on gas burners may distort the base of the pan, causing it not to adhere correctly. Power level 1-2 3-4 5 6-7-8 9 Maximum operating time in hours 6 5 4 1, 5 1, 5 16 Buzzer This can also indicate several irregularities: • An object (a pan, cutlery, etc. [. . . ] 18 Care and maintenance Switching the appliance off Disconnect your appliance from the electricity supply before carrying out any work on it. Stainless steel frame (only in models with outer frame) Stainless steel can be marked by hard water which has been left on the surface for a long time, or by cleaning products containing phosphorus. After cleaning, it is advisable to rinse the surface well and dry it thoroughly. If water is spilt on the surface, dry it quickly and thoroughly. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE XINDAK DAC-8

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual XINDAK DAC-8 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag