User manual XTANT M410 TECHNICAL DATA REPORT

[. . . ] TH E C H A R T S P R O V I D E D, O F F E R A S I MP L E METHOD O F D O C U M E N T A T I O N. OWNER'S A D D R E S S: TH I S CI T Y/ ST A T E: V E H I C L E: XT A N T A M P L I F I E R: M O D E L SETTING) ZI P: YE A R: S E R I A L# CROSSOVER MODES OF OPERATION T h e 6 0 4 x i s e q u i p p e d w i t h i n d e p e n d e n t FRONT a n d R E A R crossovers. Also includes Left and Right line out crossovers. Each crossover is controlled by four crossover mode jumpers labeled, FRONT CHAN XOVER MODE, LINE OUT MODE SELECT, REAR CHAN XOVER MODE, LINE OUT MODE SELECT. [. . . ] Each crossover is controlled by four crossover mode jumpers labeled, FRONT CHAN XOVER MODE, LINE OUT MODE SELECT, REAR CHAN XOVER MODE, LINE OUT MODE SELECT. The header jumper labeled FRONT CHAN XOVER MODE controls the crossover function as it applies to the front channels. The header jumper labeled REAR CHAN XOVER MODE controls the crossover function as it applies to the rear channels. (See illustration) The t w o header j um per s l abel ed L I N E O U T MO D E SELEC T, control the crossover function as it applies to the front and rear, left and right line outputs. (See illustration) The High and Low Pass frequencies are determined by the Frequency Modules (SIPs) installed in the four (4) SIP sockets pictured on the reverse side of this document. input sensitivity ( CIRCLE F R O N T I N P U T S ( FRONT CHANNELS) R E A R I N P U T S ( REAR CHANNELS) ­20dB ­10 dB 0dB +10dB +20 dB ­20 dB ­10 dB 0 dB +10 dB +20 dB IT IS IMPORTANT THAT YOU RETAIN THIS LOG FOR YOUR RECORDS. ON P A G E 1 2 O F T H E OWNER'S MA N U A L, Y O U W I L L F I N D T H E OWNER'S REFERENCE LOG. ONCE Y O U H A V E N O T A T E D T H E F I N A L SETTINGS F O R T H I S 6 0 4X, T R A N S F E R THOSE SETTINGS T O T H E OWNER'S REFERENCE LOG. To change frequency modules, simply remove each resistor SIP and replace it with the appropriate SIP value to achieve the desired frequency. The Low and High Pass frequencies are independent. Any combination of the available frequency modules (SIPs) may be used (ie. 80 Hz Low Pass and 120 Hz High Pass). · · · · · · · · · · · · · · · · I N S T A L L A T I O N SPECIALIST D A T E I NSTALLED ADJUST LEFT, RIGHT FRONT AND LEFT, RIGHT REAR AMPLIFIER OUTPUT LEVELS. ADJUST NOISE GATE THRESHOLD (IF USED): T u r n n o i s e g a t e o n a n d a d j u s t t h e t h r e s h o l d b y t u r ning clockwise to increase sensitivity (gate will open w i t h l e s s i n p u t s i g n a l ) . T h e g r e e n LED w i l l i l l u m i n a t e when the gate passes signal. AFTER FINE TUNING THE SYSTEM: xtant technologies · · · · · · · · · 7 6 7 6 SO U T H 4 6T H STREET PHOENIX, ARIZONA 8 5 0 4 0 U S A · · · · · · · · 602 431. 8686 Remove protective covering from amplifier and clean per the maintenance section on page 9 of the O w n e r ' s M a n u a l . Attach cover to base. · · · · · · · · · INSTALLER'S . REFERENCE. [. . . ] T h e g r e e n LED w i l l i l l u m i n a t e when the gate passes signal. AFTER FINE TUNING THE SYSTEM: xtant technologies · · · · · · · · · 7 6 7 6 SO U T H 4 6T H STREET PHOENIX, ARIZONA 8 5 0 4 0 U S A · · · · · · · · 602 431. 8686 Remove protective covering from amplifier and clean per the maintenance section on page 9 of the O w n e r ' s M a n u a l . Attach cover to base. · · · · · · · · · INSTALLER'S . REFERENCE. . M410 . CROSSOVER FREQUENCY SELECTION: TO CHANGE THE FREQUENCY OF EITHER THE HIGH AND/OR LOW P ASS FILTERS, REPLACE THE 90 HZ FREQUENCY MODULE (SIP) INSTALLED ON THE CIRCUIT BOARD. [. . . ]