User manual XTANT M810 TECHNICAL DATA REPORT

[. . . ] TH E C H A R T S P R O V I D E D, O F F E R A S I MP L E METHOD O F D O C U M E N T A T I O N. OWNER'S A D D R E S S: TH I S CI T Y/ ST A T E: V E H I C L E: XT A N T A M P L I F I E R: M O D E L SETTING) ZI P: YE A R: S E R I A L# CROSSOVER MODES OF OPERATION T h e 6 0 3 x i s e q u i p p e d w i t h i n d e p e n d e n t FRONT a n d R E A R crossovers. Each crossover is controlled by two (2) c r o s s o v e r m o d e j u m p e r s l a b e l e d A M P & L I N E X O V R. T h e header jumper labeled AMP XOVR control the crossover function as it applies to the 603x's Front (stereo) and Rear (mono) amplifier. [. . . ] T h e header jumper labeled AMP XOVR control the crossover function as it applies to the 603x's Front (stereo) and Rear (mono) amplifier. The modes of operation are: Position 1 = Bypass (Full Range), Position 2 = High Pass, and Position 3 = Low Pass. (See illustration) The two (2) header jumpers labeled LINE XOVR c o n t r o l t h e c r o s s o v e r f u n c t i o n a s i t a p p l i e s t o t h e 6 0 3 x ' s FRONT a n d REAR RCA Line Outputs. The modes of operation are: Position 1 = Bypass (Full Range), Position 2 = High Pass, and Position 3 = Low Pass. (See illustration ) The High and Low Pass frequencies are determined by the Frequency Modules (SIPs) installed in the four (4) SIP sockets pictured on the reverse side of this document. input sensitivity ( CIRCLE F R O N T I N P U T S ( 2 CHANNELS) R E A R I N P U T S ( MONO CHANNEL) ­20dB ­10 dB 0dB +10dB +20 dB CHANNELS) ­20 dB ­10 dB 0 dB +10 dB +20 dB IT IS IMPORTANT THAT YOU RETAIN THIS LOG FOR YOUR RECORDS. ON P A G E 1 2 O F T H E OWNER'S MA N U A L, Y O U W I L L F I N D T H E OWNER'S REFERENCE LOG. ONCE Y O U H A V E N O T A T E D T H E F I N A L SETTINGS F O R T H I S 6 0 3X, T R A N S F E R THOSE SETTINGS T O T H E OWNER'S REFERENCE LOG. To change frequency modules, simply remove each resistor SIP and replace it with the appropriate SIP value to achieve the desired frequency. The Low and High Pass frequencies are independent. Any combination of the available frequency modules (SIPs) may be used (ie. 80 Hz Low Pass and 120 Hz High Pass). · · · · · · · · · · · · · · · · & MONO AMPLIFIER OUTPUT LEVELS. (IF USED): T u r n n o i s e g a t e o n a n d a d j u s t t h e t h r e s h o l d b y t u r ning clockwise to increase sensitivity (gate will open w i t h l e s s i n p u t s i g n a l ) . T h e g r e e n LED w i l l i l l u m i n a t e when the gate passes signal. AFTER FINE TUNING THE SYSTEM: xtant technologies · · · · · · · · · 7 6 7 6 SO U T H 4 6T H STREET PHOENIX, ARIZONA 8 5 0 4 0 U S A · · · · · · · · 602 431. 8686 Remove protective covering from amplifier and clean per the maintenance section on page 9 of the O w n e r ' s M a n u a l . Attach cover to base. · · · · · · · · · INSTALLER'S . REFERENCE. . M810 . CROSSOVER FREQUENCY SELECTION: TO CHANGE THE FREQUENCY OF EITHER THE HIGH AND/OR LOW P ASS FILTERS, REPLACE THE 90 HZ FREQUENCY MODULE (SIP) INSTALLED ON THE CIRCUIT BOARD. [. . . ] T h e g r e e n LED w i l l i l l u m i n a t e when the gate passes signal. AFTER FINE TUNING THE SYSTEM: xtant technologies · · · · · · · · · 7 6 7 6 SO U T H 4 6T H STREET PHOENIX, ARIZONA 8 5 0 4 0 U S A · · · · · · · · 602 431. 8686 Remove protective covering from amplifier and clean per the maintenance section on page 9 of the O w n e r ' s M a n u a l . Attach cover to base. · · · · · · · · · INSTALLER'S . REFERENCE. . M810 . CROSSOVER FREQUENCY SELECTION: TO CHANGE THE FREQUENCY OF EITHER THE HIGH AND/OR LOW P ASS FILTERS, REPLACE THE 90 HZ FREQUENCY MODULE (SIP) INSTALLED ON THE CIRCUIT BOARD. [. . . ]