User manual YAESU FC-40 INSTALLATION INSTRUCTIONS

[. . . ] 1 Ferrite Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 U-bolt Kit · U-bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 · Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 · Washers (FW6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] After mounting the FC-40, connect the cables from the FC-40 to the ANT and TUNER (or CAT/LINEAR) jacks (depends on the transceiver) on the rear panel of the transceiver. Refer to the transceiver's Operating Manual for details of the interconnections with the transceiver. If you use the FC-40 with the Yaesu FT-857D/-897D transceiver, refer to the instructions on the opposite page of this manual for interconnection details. Screw (5x20) Outer washer (OW5) Screw (5x20) Outer washer (OW5) Washer (FW5) Nut (N6) Spring washers (SW6) Washer (FW6) Washer (FW5) Tuner Operation Please see your transceiver's Operating Manual for operation with the FC-40 Tuner. See the instructions at the right side of this page for operation of the FC-40 with FT-857/-897 transceivers. FT-857D/-897D Tuner Operation 1. Press and hold in the F ( FUNC ) key for one second to activate the Menu mode. Rotate the MEM/VFO CH (FT-857D: SELECT ) knob to recall Menu Mode No-001 [EXT MENU], then rotate the DIAL to change the setting to "ON to enable the extended Menu ON" ON Mode. Rotate the MEM/VFO CH (FT-857D: SELECT ) knob to recall Menu Mode No-020 [CAT LIN TUN]. The default setCAT/LIN LIN/TUN ting for this Menu is "CAT Rotate the DIAL to change the CAT. " CAT setting to "TUNER TUNER. " TUNER 4. Press and hold in the F ( FUNC ) key for one second to save the new setting and exit, then turn the transceiver off. Set up the FC-40 and FT-897D/-857D per the illustration on the opposite page of this manual, then turn on the transceiver's power again. Do not set up the FC-40 and FT-897D/-857D before changing the Menu Mode, item No-020 [CAT/LIN/TUN]. Press and hold in the F ( FUNC ) key for one second to activate the Menu mode. Rotate the MEM/VFO CH (FT-857D: SELECT ) knob to recall Menu Mode No-085 [TUNER ATAS]. The default setting for TUNER/ATAS this Menu is "OFF Rotate the DIAL to change the setting to OFF. " OFF "TUNER TUNER. " TUNER 8. Press and hold in the F ( FUNC ) key for one second to save the new setting and exit. Press the F ( FUNC ) key, as needed, to recall Multi Function Row "k" [TUNE DOWN UP]. Press the [A](TUNE) key to turn the FC-40 on. "Parentheses" will appear on both sides of the "TUNE indication, and TUNE" TUNE "TUNR" will appear on the LCD. "TUNR" MEM/VFO CH BAT T-A BAT T-B Microprocessor Resetting By changing the configuration of an internal DIP switch, the microprocessor in the FC-40 may be reset. Do this in the event of erratic operation of the tuner, or to clear the tuner's memories. Remove the 8 screws affixing the case of the FC-40, then remove the case. Turn the 4th switch of S1003 to "on". D1002 will glow green briefly, then turn off. [. . . ] Please check the antenna and coax if this happens. Take appropriate measures to ensure that there is no possibility that someone may come in contact with the antenna or FC-40 ANT terminal while your station is transmitting. Observe all practical and regulatory requirements for protecting yourself and the public from the effects of radio frequency radiation from your antenna system. FT-897D "TUNR" FT-857D GND Lug S1002 No. Press and hold in the [A](TUNE) key to initiate automatic tuning. [. . . ]