User manual YAESU FL-2100Z

[. . . ] 2 Accessories & Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Note: Once deleted, the channel data cannot be recovered. 34 FL-2100ZR Operating Manual MEMORY OPERATION REGULAR MEMORY CHANNEL OPERATION HOME Channel Memory A special one-touch "HOME" channel is available (one for each of the five operating bands: see page 21), to allow quick recall of a favorite operating frequency on each band. Memory storage is simple to accomplish: 1. Select the desired frequency, while operating in the VFO mode on the "Main" band. Be sure to set up any desired CTCSS or DCS tones, as well as any desired repeater offset. The power level may also be set at this time, if you wish to store it. Press and hold in the [SET] key for 1/2 second. A memory number will appear (blinking) on the display. While the memory channel number is blinking, just press the "Main" [H/M] key. The frequency and other data (if any) will now be stored in the special HOME channel register. You may repeat this process on the other operating bands. To recall the HOME channel, just press the [H/M] key while operating either in the VFO or MR mode. FL-2100ZR Operating Manual 35 MEMORY OPERATION REGULAR MEMORY CHANNEL OPERATION Memory Bank Operation Memory Bank Assignment 1. The current (original) configuration will lost when you recall the Hyper Memory Channel. To prevent this from happening, press and hold in the Hyper Memory key (generally the [1] key) to store the current configuration into that Hyper Memory Channel before recalling the Hyper Memory Channel, or set Menu #16 to enable the Automatic Writing feature for the Hyper Memory. See page 63 for details. FL-2100ZR Operating Manual 37 SCANNING The FL-2100ZR allows you to scan just the memory channels, the entire operating band, or a portion of that band. It will halt on signals encountered, so you can talk to the station(s) on that frequency, if you like. Scanning operation is basically the same in each of the above modes. Before you begin, take a moment to select the way in which you would like the scanner to resume scanning after it halts on a signal. Setting the Scan-Resume Technique Two options for the Scan-Resume mode are available: TIME: In this mode, the scanner will halt on a signal it encounters, and will hold there for five seconds. If you do not take action to disable the scanner within five seconds, the scanner will resume even if the stations are still active. BUSY: In this mode, the scanner will halt on a signal it encounters. Two seconds after the carrier has dropped because the other station(s) ceased transmission, the scanner will resume. Press the [SET] key momentarily to enter the Set mode. Rotate the "Main" band DIAL knob to select Menu #34 (SCAN). [. . . ] MSM: The scanner will "only scan" the flagged (Preferential) channels during scanning. Menu #38 [STEP] Function: Sets the Synthesizer steps. Available Values: 5. 0 k/10. 0 k/12. 5 k/15. 0 k/20. 0 k/25. 0 k/50. 0 k Default: Depends on the band of operation. Note: This Menu Item can be set independently for each band. 66 FL-2100ZR Operating Manual MENU ("SET") MODE Menu #39 [SPCONT] Function: Defines the audio path to the external speaker (when used). [. . . ]