User manual YAESU FT-2900R

[. . . ] FM TRANSCEIVER FT-2900R OPERATING MANUAL VERTEX STANDARD CO. , LTD. VERTEX STANDARD YAESU UK LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan US Headquarters 10900 Walker Street, Cypress, CA 90630, U. S. A. Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U. K. VERTEX STANDARD HK LTD. Unit 5, 20/F. , Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong VERTEX STANDARD (AUSTRALIA) PTY. , LTD. Normanby Business Park, Unit 14/45 Normanby Road Notting Hill 3168, Victoria, Australia Contents FT-2900R Quick Reference Guide Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2) The PMS memory channels (L0/U0 through L9/U9) may not be assigned to a Memory Bank. Memory Bank Recall 1. Press the [D/MR(MW)] key, if needed, to enter the Memory mode. Press the Microphone's [ ] key to activate the "Memory Bank" mode. The Memory Bank number will appear on the display. Press the [#] key to increment the Memory Bank ("b1 b1 through "b8 b8"). Rotate the DIAL knob to select the memories within the selected Bank; you will observe that you can only select memory channels in the current memory bank. The small memory bank number will appear, to the right of the frequency display, two seconds after you complete memory channel selection while operating within a Memory Bank. To change to another Memory Bank, press the [#] key to step up to the next-highest bank. To exit from Memory Bank operation, just press the Microphone's [ ] key. The Memory Channel number will appear steadily on the right side of the display, indicating that you are now in the "standard" Memory Recall mode, without utilization of the Memory Banks. The memories stored in the various Banks will remain in those banks, however; you do not need to store them again. FT-2900R OPERATING MANUAL 39 MEMORY OPERATION MEMORY BANK OPERATION Removing Memories from a Memory Bank 1. While operating in the Memory Bank mode, recall the memory channel to be removed from a Memory Bank. Press and hold in the [D/MR(MW)] key for one second, then press the [A/N(LOW)] key to remove the memory channel data from the Memory Bank. You must first enter the Memory Bank mode, by pressing the microphone's [ key, before attempting to remove a channel from a Bank. If you don't, "MCHERR" will appear when you press the [A/N(LOW)] key in step (2) above. ] Changing a Memory Bank's Name You may change the default Memory Bank Name, which is indicated on the display when you've selected a Memory Bank, to a different name, if desired. Press and hold in the [MHz(SET)] key for one second, then rotate the DIAL knob to select "9 BNK NM NM. " 9 2. Press the [MHz(SET)] key momentarily, then rotate the DIAL knob to recall the memory bank on which you wish to change a label. Press the [A/N(LOW)] key to enable changing of the name tag. Rotate the DIAL knob to select the first digit of the desired label. Press the [A/N(LOW)] key to move to the next character. If you make a mistake, press the [REV(DW)] key to back-space the cursor, then re-enter the correct letter, number, or symbol. [. . . ] D TONE: Encodes a DCS code and Decodes a CTCSS tone. 49 SQL. TYP Function: Selects the Tone Encoder and/or Decoder mode. Available Values: TONE / TSQL / DCS / RV TN / OFF Default: OFF TONE: CTCSS Encoder TSQL: CTCSS Encoder/Decoder DCS: Digital Coded Encoder/Decoder RV TN: Reverse CTCSS Decoder (Mutes receiver when matching tone is received) Note: See also Set Mode Item "48 SPLIT" regarding additional selections available during "Split Tone" operation. 50 STEP Function: Sets the Synthesizer steps. [. . . ]