Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual YAESU FT-450D. We hope that this YAESU FT-450D user guide will be useful to you.
Lastmanuals help download the user guide YAESU FT-450D.
You may also download the following manuals related to this product:
YAESU FT-450D BROCHURE (2349 ko)
Manual abstract: user guide YAESU FT-450D
Detailed instructions for use are in the User's Guide.
[. . . ] HF/50 MHZ TRANSCEIVER
FT-450D
OPERATION MANUAL
VERTEX STANDARD CO. , LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
VERTEX STANDARD
US Headquarters 10900 Walker Street, Cypress, CA 90630, U. S. A.
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U. K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F. , Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong
VERTEX STANDARD (AUSTRALIA) PTY. , LTD.
Normanby Business Park, Unit 14/45 Normanby Road Notting Hill 3168, Victoria, Australia
TABLE
OF
CONTENTS
SSB/AM MODE TRANSMISSION . . . . . . . . . . . . . . . . . . . . . 36
TX METER SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 TX POWER ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 TRANSMITTER TIME-OUT TIMER (TOT) . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the [DSP/SEL] knob to enable adjustment of this Menu Item. The " " icon will be blinking. Rotate the [DSP/SEL] knob to select the desired function. The " " icon returns to appear continuously. Press and hold the [F] button for one second to return to normal operation.
[DSP/SEL] knob
[F] button
Page 44
FT-450D OPERATION MANUAL
SSB/AM MODE TRANSMISSION
NOTE
FT-450D OPERATION MANUAL
Page 45
CW MODE OPERATION
The powerful CW operating capabilities of the FT-450D include operation using both an electronic keyer paddle and a "straight key" or emulation thereof, as is provided by a computer-based keying device.
SETUP FOR STRAIGHT KEY (AND STRAIGHT KEY EMULATION) OPERATION
Before starting, connect your key to the front panel KEY jack in the status that turned off the [POWER(ON/OFF)] switch, and be sure the [KEYER] button is turned off (the " " icon is not displayed) for now. Press the [BAND ]/[BAND ] buttons to select the operating band. By pressing the [BAND ]/[BAND ] buttons, the operating band will change as follows. 7 10 14 15 18 21 24. 5 28 50 1. 8 3. 5 7 . . . . . . Press the [MODE ]/[MODE ] buttons to select the CW mode. Rotate the [MAIN DIAL] knob to adjust the operating frequency. If you use the MH-31A8J (or MD-100A8X: option), you may adjust the operating frequency by the [UP]/[DWN] buttons on the microphone. Press the [F] button followed by the [STO/VOX] button to engage automatic activation of the transmitter when you close the CW key. The " " icon will appear in the display. When you close your CW key, the transmitter will automatically be activated, and the CW carrier will be transmitted. When your release the key, transmission will cease after a brief delay. The delay time is user-programmable, per the discussion on page 48. NOTE: Do not use the plug except the 3. 5-mm 3-pin type plug. If the plug in correct size is not used the radio may be harmed or damaged.
[MODE ]/[MODE ] button [STO/VOX] button [BAND ]/[BAND ] button
[MAIN DIAL] knob [KEYER] button
[F] button
NOTICE
Regarding of the [DSP/SEL] knob The [DSP/SEL] knob is used for operating various functions depending on the situation. If you can not change the frequency/memory channel by tuning the [DSP/SEL] knob, the [DSP/SEL] knob is selected to operate of one of the DSP functions. In this case, press the [DSP] button several times until the ">" icon disappears from the DSP Graphic Display.
Page 46
FT-450D OPERATION MANUAL
CW MODE OPERATION
USING THE BUILT-IN ELECTRONIC KEYER
Before starting, connect your keyer paddle to the front panel KEY jack in the status that turned off the [POWER(ON/ OFF)] switch. Press the [BAND ]/[BAND ] buttons to select the operating band. By pressing the [BAND ]/[BAND ] buttons, the operating band will change as follows. [. . . ] NOTE: The supplied double-sided adhesive tape may be used to temporarily hold the mobile mounting bracket in place, while drilling the holes for installation.
Upper side
Lower side
Stay (user prepared)
2. Position the transceiver in the bracket so the holes in the side are aligned with those in the bracket. Fasten the transceiver into place using the supplied Knob-screws (M4).
M4 Knob-screws (4 pcs)
FT-450D OPERATION MANUAL
Page 95
SPECIFICATIONS
General
Rx Frequency Range: Tx Frequency Ranges: Frequency Stability: Operating Temperature Range: Emission Modes: Frequency Steps: Antenna Impedance: Power Consumption: Supply Voltage: Dimensions (WxHxD): Weight (approx. ): 30 kHz - 56 MHz (operating) 160 - 6 m (specified performance, Amateur bands only) 160 - 6 m (Amateur bands only) ±1 ppm/hour (@+25 °C, after warmup) 14 °F ~ 122 °F (10 °C ~ +50 °C) A1A (CW), A3E (AM), J3E (LSB, USB), F3E (FM) 10 Hz (SSB & CW), 100 Hz (AM & FM) 50 Ohms, unbalanced Rx (signal present) 1. 5 A Tx (100 W) 22 A DC 13. 8 V ± 10% 9' x 3. 3" x 8. 5" (229 x 84 x 217 mm) 8. 8 lb (4. 0 kg)
Transmitter
100 watts (25 watts AM carrier) J3E (SSB): Balanced, A3E (AM): Low-Level (Early Stage), F3E (FM): Variable Reactance Maximum FM Deviation: ±5. 0 kHz / ±2. 5 kHz Harmonic Radiation: Better than 60 dB (160 - 10m Amateur bands) Better than 70 dB (6m Amateur band) SSB Carrier Suppression: At least 60 dB below peak output Undesired Sideband Suppression: At least 60 dB below peak output Audio Response (SSB): Not more than 6 dB from 300 to 2400 Hz Microphone Impedance: 600 Ohms (200 to 10 kOhms) Power Output: Modulation Types:
Page 96
FT-450D OPERATION MANUAL
SPECIFICATIONS
Receiver
Circuit Type: Intermediate Frequencies: Sensitivity (IPO "OFF", ATT: OFF): Double-conversion superheterodyne 67. 899 MHz / 24 kHz SSB (2. 4 kHz, 10 dB S+N/N) 0. 25 µV (1. 8 - 2. 0 MHz) 0. 25 µV (3. 5 - 30 MHz) 0. 20 µV (50 - 54 MHz) AM (6 kHz, 10 dB S+N/N, 30 % modulation @400 Hz) 2. 00 µV (1. 8 - 2. 0 MHz) 2. 00 µV (3. 5 - 30 MHz) 1. 00 µV (50 - 54 MHz) FM (BW: 15 kHz, 12 dB SINAD) 0. 50 µV (28 - 30 MHz) 0. 30 µV (50 - 54 MHz) There is no specification in frequency ranges not listed. SSB/CW/AM 2. 50 µV (1. 8 - 30 MHz) 1. 00 µV (50 - 54 MHz) FM 0. 32 µV (28 - 30 MHz) 0. 16 µV (50 - 54 MHz) There is no specification in frequency ranges not listed. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE YAESU FT-450D
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual YAESU FT-450D will begin.