User manual YAESU FT-7100M

[. . . ] OPERATING MANUAL VERTEX STANDARD CO. , LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 17210 Edwards Rd. , Cerritos, CA 90703, U. S. A. 52nd Terrace, Suite 201, Miami, FL 33166, U. S. A. YAESU EUROPE B. V. P. O. Box 75525, 1118 ZN Schiphol, The Netherlands YAESU UK LTD. Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U. K. YAESU GERMANY GmbH Am Kronberger Hang 2, D-65824 Schwalbach, Germany VERTEX STANDARD HK LTD. 11th Floor Tsim Sha Tsui Centre, 66 Mody Rd. , Tsim Sha Tsui East, Kowloon, Hong Kong Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the [BAND] key to start scanning for the incoming CTCSS or DCS tone/code. When the radio detects the correct tone or code, it will halt on that tone/code, and audio will be allowed to pass. Press the [BAND] key to lock in that tone/code and exit to normal operation. CTCSS Bell Paging Bell Paging adds an alert ringer to CTCSS tone squelch operation, for added convenience. When you receive a call with a matching CTCSS tone, the ringer sounds to alert you to the presence of the incoming call. To activate CTCSS Bell operation, press the [TONE] key until " " appears on the display. . As before, calls without a matching CTCSS tone will be ignored. Those with a matching tone will cause the transceiver to ring as the squelch opens while the caller transmits. Note that other stations do not need to have the CTCSS Bell function to call you; they can just use standard CTCSS encoding. When you reply to a CTCSS Bell call, you may want to turn off the Bell function, or else the transceiver will ring every time your squelch opens. You can store CTCSS Bell Paging as a "tone mode" in a memory, as you can do with different CTCSS/DCS tone and encode/decode status. 1750 Hz Tone Calling (European Versions) In the European versions of the FT-7100M, press the [P1] (MH-48A6J) or [ACC] (MH42B6JS) button on the microphone to transmit a 1750 Hz Burst Tone for repeater access. If you own a non-European version of the FT-7100M, but plan on visiting a country which requires a 1750 tone for repeater access, you may use menu #20 to set up the [P1] (MH48A6J) or [ACC] (MH-42B6JS) button for 1750 Hz Tone operation. See page 43 for details. FT-7100M Operating Manual 27 OPERATION TRANSMISSION DTMF Tone Generation (MH-48A6J only) The white keys (with numbers, letters, or the Ú/# characters printed on them) on the microphone may be used for manual sending of DTMF tones for autopatch or repeater control use. Just press the PTT switch, and hold it in, while pressing the desired keys. DTMF Autodialer Operation Sixteen DTMF Autodialer memories are available on the FT-7100M. These DTMF Autodialer memories can store up to 16 digits of a telephone number for repeater autopatch or other use. To load DTMF Autodialer memories, use following procedure: 1. Press and hold the [BAND] key for 1/2 second to activate the "Menu" mode. Rotate the Main Dial knob to select Menu # 14 (DTMFW ). Press the [BAND] key momentarily to enable changing of this Menu item. Rotate the Main Dial knob to select the DTMF Autodialer memory channel number into which you wish store a telephone number ("CH-01" ~ "CH-16"). Use the Main Dial knob (or the microphone's [UP]/ [DWN] buttons) to select the first digits of the telephone DTMF Autodialer Memory number you wish to store. When you have selected the correct digit, press the [LOW] Current Digit key momentarily. Now, use the Main Dial knob (or the microphone's [UP]/ [DWN] buttons) to select the second of 16 available digits in the current DTMF Autodialer memory. [. . . ] Note: This Menu item can be set independently for each band. FT-7100M Operating Manual 53 MENU SYSTEM MENU SELECTION DETAILS Menu Item 27 [STEP] Function: Setting the synthesizer steps. Available Values: 5. 0/10. 0/12. 5/15. 0/20. 0/25. 0/50. 0 kHz Default Setting: Depends on transceiver version. Note: This Menu item can be set independently for each band. Menu Item 28 [SPCNT] Function: Defining the audio path to the external speaker (when used). [. . . ]