User manual YAESU FT-7800R

[. . . ] DUAL BAND FM TRANSCEIVER FT-7800R OPERATING MANUAL VERTEX STANDARD CO. , LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U. S. A. YAESU EUROPE B. V. P. O. Box 75525, 1118 ZN Schiphol, The Netherlands YAESU UK LTD. Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U. K. VERTEX STANDARD HK LTD. Unit 5, 20/F. , Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Accessories & Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] However, the "Hyper Memory" Mode allows you to store the total current configuration of the radio into a special "Hyper" memory bank. Hyper Memory Storage 1. Set up the transceiver according to the desired configuration. Press and hold in, for two seconds, the Hyper Memory key ([1] through [5]), corresponding to the Hyper Memory channel into which you wish to store this configuration. Hyper Memory Recall Press the appropriate Hyper Memory key ([1] through [5]) to recall the desired Hyper Memory channel. On Hyper Memory Channels "2" through "5, " the current (original) configuration will lost when you recall any other Hyper Memory Channel. To prevent this from happening, press and hold in the (current) Hyper Memory key to store the current configuration into that Hyper Memory Channel before recalling anothe Hyper Memory Channel, or set Menu #17 (HYPER) to enable the Automatic Writing feature for all Hyper Memories, including Hyper Memory "1. " See page 70 for details. 38 FT-7800R OPERATING MANUAL MEMORY OPERATION WEATHER BROADCAST CHANNEL OPERATION The VHF Weather Broadcast Station Memory Channel Bank has been pre-programmed at the factory, for quick selection of NOAA weather information stations. Press and hold in the [LOW(ACC)] key for 1/2 second to recall the Weather Broadcast Station Memory Channel Bank. Rotate the DIAL knob to select the desired Weather Broadcast channel. If you wish to scan this bank to search for louder CH FREQUENCY CH stations, just press the PTT switch. When the scan- 1 162. 550 MHz 6 ner pauses on a station, press the PTT key once 2 165. 400 MHz 7 3 162. 475 MHz 8 to halt the can, or press it twice to restart the scan. To exit to normal operation, press and hold in the 5 162. 450 MHz 10 [LOW(ACC)] key for 1/2 second. FREQUENCY 162. 500 MHz 162. 525 MHz 161. 650 MHz 161. 775 MHz 163. 275 MHz Severe Weather Alert In the event of extreme weather disturbances, such as storms and hurricanes, the NOAA (National Oceanic and Atmospheric Administration) sends a weather alert accompanied by a 1050 Hz tone and subsequent weather report on one of the NOAA weather channels. FT-7800R OPERATING MANUAL 39 SCANNING The FT-7800R allows you to scan just the memory channels, the entire operating band, or a portion of that band. It will halt on signals encountered, so you can talk to the station(s) on that frequency, if you like. Scanning operation is basically the same in each of the above modes. Before you begin, take a moment to select the way in which you would like the scanner to resume scanning after it halts on a signal. Setting the Scan-Resume Technique Three options for the Scan-Resume mode are available: BUSY: In this mode, the scanner will halt on a signal it encounters. Two seconds after the carrier has dropped because the other station(s) ceased transmission, the scanner will resume. TIME: In this mode, the scanner will halt on a signal it encounters, and will hold there for five seconds. If you do not take action to disable the scanner within five seconds, the scanner will resume even if the stations are still active. HOLD: In this mode, the scanner will halt on a signal it encounters. It will not restart automatically; rotate the DIAL knob to re-initiate scanning if you wish to resume. Press and hold in the [BAND(SET)] key for 1/2 second to enter the Set mode. Rotate the DIAL knob to select Menu #37 (SCAN). Press the [BAND(SET)] key momentarily, then rotate the DIAL knob to select the desired scan-resume mode. Press the [BAND(SET)] key momentarily to save the new setting, then press and hold in the [BAND(SET)] key for 1/2 second to exit to normal operation. [. . . ] SKIP: The scanner will "skip" the flagged ("SKIP") channels during scanning. ONLY: The scanner will only scan the flagged (Preferential) channels during scanning. Menu #41 [SPLIT] Function: Enables/Disables split CTCSS/DCS coding. Available Values: SPL. OFF/SPL. ON Default: SPL. OFF When this Menu Item is set to "ON, " you can see the following additional parameters after the "DCS" parameter while selecting the Menu #42: SQL. TYP. [. . . ]