User manual YAESU FT-8800

[. . . ] DUAL BAND FM TRANSCEIVER FT-8800R OPERATING MANUAL VERTEX STANDARD CO. , LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U. S. A. 52nd Terrace, Suite 201, Miami, FL 33166, U. S. A. YAESU EUROPE B. V. P. O. Box 75525, 1118 ZN Schiphol, The Netherlands YAESU UK LTD. Unit 12, Sun Valley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U. K. VERTEX STANDARD HK LTD. Unit 5, 20/F. , Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press and hold in the [SET] key for 1/2 second to copy the memory channel data into the Memory Bank. The PMS memory channel (L1/U1 through L10/U10) does not assign to the memory bank. Set the radio to the Memory mode by pressing the [V/M] key, if necessary. Press and hold in the [V/M] key for 1/2 second, then rotate the "Main" band DIAL knob to select the Memory Bank ("BANK1" ~ "BANK10" ). Press the [SET] key momentarily to lock in the selected Memory Bank. In the Memory Bank mode of operation, you can only select memory channels in the current memory bank. To change the Memory Bank to another Bank, press and hold in the [V/M] key for 1/2 seconds, then rotate the "Main" band DIAL knob. To exit from Memory Bank operation, press and hold in the [V/M] key for 1/2 second, then rotate the "Main" band DIAL knob to select "ALL. MEM, " then press the [SET] key momentarily. Deleting a Memory Channel from a Memory Bank 1. In the Memory Bank mode, recall the memory channel to be deleted from the Memory Bank. Press and hold in the [V/M] key for 1/2 second, then press and hold in the [SET] key for 1/2 second to delete the Memory Channel from the Memory Bank. Memory Only Mode Once memory channel programming has been completed, you may place the radio in a "Memory Only" mode, whereby VFO operation is impossible. This may be particularly useful during public-service events where a number of operators may be using the radio for first time, and ultimate simplicity of channel selection is desired. To place the radio into the Memory Only mode: 1. Press and hold in the "left" [V/M] key while turning the radio on. Rotate the "right" DIAL knob to select the (F-6 M-ONLY MODE), then press the [SET] key momentarily. To return to normal operation, repeat the above steps. 36 FT-8800R Operating Manual MEMORY OPERATION HYPER MEMORY MODE The FT-8800R usually stores, into memory, the operating frequency and some aspects of operating status (such as CTCSS/DCS data, repeater shift, power level etc. ). However, the "Hyper Memory" Mode allows you to store the total current configuration of the radio into a special "Hyper" memory bank. For example, a Hyper Memory location may store the frequencies of both the "Left" and "right" bands, plus Scanning features, etc. Hyper Memory Storage 1. Set up the transceiver according to the desired configuration. Press and hold in the Hyper Memory key ([1] through [6]), corresponding to the Hyper Memory channel into which you wish to store this configuration, for 2 seconds. Hyper Memory Recall Press the appropriate Hyper Memory key ([1] through [6]) to recall the desired Hyper Memory channel. The current (original) configuration will lost when you recall the Hyper Memory Channel. To prevent this from happening, press and hold in the Hyper Memory key (generally the [1] key) to store the current configuration into that Hyper Memory Channel before recalling the Hyper Memory Channel, or set Menu #16 to enable the Automatic Writing feature for the Hyper Memory. [. . . ] Available Values: EXT/OFF/ INT. EXT/INT Default: EXT EXT: The audio is routed to external speaker (internal speaker is off). OFF: The audio is not routed (internal and external speakers are both off). INT. EXT: The audio is routed to both the internal and external speakers. INT: The audio is routed to the internal speaker only (external speaker is off). [. . . ]