User manual YAESU FTDX9000 DATA MANAGEMENT OPERATION MANUAL

[. . . ] FTDX9000MP/Contest Data Management OPERATION MANUAL FT DX 9000MP/CONTEST DATA MANAGEMENT OPERATION MANUAL PLEASE READ THIS FIRST When turning on the transceiver for the first time, please set the local time as soon as possible. If this is not done, the various functions of the World Clock and Great Circle Map will not function correctly. Note: If you wish to add a city to the City List that was programmed at the factory, you will need to supply your own USB or PS/2 Keyboard. If you utilize one of the pre-loaded cities, a keyboard is not necessary. [. . . ] By pressing the [7/18](CTR/FIX) key repeatedly, the CTR mode and the FIX mode will be toggled alternately. By pressing the [2/3. 5](SPAN) key, you can set the bandwidth of the span viewed using the Spectrum Scope. By pressing the [2/3. 5](SPAN) key, the span will change as follows. 25 kHz 50 kHz 100 kHz 250 kHz 500 kHz 1000 kHz 2500 kHz 25 kHz . . . . . . Press the [3/5](ATT) key to set the desired attenuation value. By pressing the [3/5](ATT) key, the attenuation will change as follows. By pressing the [6/14](LBWS) key, the LBWS segment width will change as follows. NORMAL LBWS-1(50%) LBWS-2(30%) LBWS-3(10%) NORMAL . . . . . . Press the [4/7](A/B) key to select the Main (VFOA) or Sub (VFO-B) VFO. Advice:Please note that the LBWS feature can not be used in the FIX mode. While LBWS is engaged, it is not possible to switch to the dual display mode. In the case of the Contest version, the [RX] switch to the left of the [CLAR/VFO-B] knob will, when pushed, cause both the VFO itself and the Spectrum Scope display to change to VFO-B. Additionally, when the optional RXU-9000 Dual Receive Unit is installed, you may use the [4/7](A/B) key to make this change, just like on the MP version. "LBWS" Select "LBWS" Select Page 18 FT DX 9000MP/CONTEST DATA MANAGEMENT OPERATION MANUAL SPECTRUM SCOPE USING THE FIX (FIXED) MODE This feature is convenient when you want to monitor an entire amateur band. The starting point, located at the left edge of the screen, can be set via the Menu. Even if the screen span (bandwidth) is changed, the start frequency will not be changed. By watching the screen, you can move your operation to frequencies where interesting activity appears on the display. Just as with the CTR mode, it is possible to toggle the Main (VFO-A) or Sub (VFO-B) VFOs. It is also possible to utilize a dual display, with the Main (VFO-A) VFO in the upper position, and the Sub (VFO-B) VFO below. By pressing the [7/18](CTR/FIX) key, it is possible to switch between the CTR mode and the FIX mode. Press the [2/3. 5](SPAN) key to set the desired value for the Span (bandwidth). By pressing the [2/3. 5](SPAN) key, the span will change as follows. 25 kHz 50 kHz 100 kHz 250 kHz 500 kHz 1000 kHz 2500 kHz 25 kHz . . . . . . [. . . ] Use the [Main Tuning Dial] knob, or the the [6/ 14]( )/[7/18]( ) keys, to select the Menu item you wish to work on. Use the [CLAR/VFO-B] knob, or the [4/7]( )/ [5]( ) keys, to change the setting of the selected Menu item. Press the [MNU] key is pressed for 2 seconds to save (within the transceiver) the new setting; the menu screen will close, and you will then return to the screen that was in use before entering the menu mode. If you press the [MNU] key momentarily to exit, the new settings will not be saved, and you will exit from the menu mode without retaining the new configuration. MENU MODE RESET 1. [. . . ]