User manual YAESU FTDX9000MP

[. . . ] FTDX9000MP/Contest Data Management OPERATION MANUAL FT DX 9000MP/CONTEST DATA MANAGEMENT OPERATION MANUAL PLEASE READ THIS FIRST When turning on the transceiver for the first time, please set the local time as soon as possible. If this is not done, the various functions of the World Clock and Great Circle Map will not function correctly. Note: If you wish to add a city to the City List that was programmed at the factory, you will need to supply your own USB or PS/2 Keyboard. If you utilize one of the pre-loaded cities, a keyboard is not necessary. [. . . ] 25 kHz 50 kHz 100 kHz 250 kHz 500 kHz 1000 kHz 2500 kHz 25 kHz . . . . . . Press the [3/5](ATT) key to set the desired attenuation value. By pressing the [3/5](ATT) key, the attenuation will change as follows. Press the [4/7](A/B) key to toggle between the Main (VFO-A) and Sub (VFO-B) VFOs. Press the [5/10](DUAL) key to engage dual spectral display. The Main VFO will appear in the upper display field, and the Sub VFO will appear in the lower. When you rotate the Main Tuning knob for Main (VFO-A) or CLAR/VFO-B knob for Sub (VFOB), the yellow arrow " " will move to follow your receive frequency. If the receive frequency is outside of the screen, the position of the operating frequency will be "shown" in the lower area of the display as "<<" ">>", and "RCV Freq is out of range" will also be displayed. Just as in the CTR mode, you can use the Marker. Please see page 14 for information on using the marker. Advice: In either CTR or FIX mode, the current operating frequency will be indicated on the screen by the yellow arrow " . " "SPAN" Select "ATT" Select "FIX/CRT" Select Advice:In the case of the Contest version, the RX switch to the left of the CLAR/VFO-B knob will, when pushed, cause both the VFO itself and the Spectrum Scope display to change to VFO-B. Additionally, when the optional RXU-9000 Dual Receive Unit is installed, you may use the [5/10](DUAL) key to enable Dual-band Spectrum Scope operation, just like on the MP version. SETTING THE LEFT EDGE FREQUENCY FOR THE FIX MODE Press the [MNU] key momentarily to enter the Menu mode. Select the item which you want to change by rotating the Main dial (in this case, the items will be in the range from SCOPE "107: MAIN FIX 1. 8 MHz" to "128: SUB FIX 50MHz"). Now you may change the setting by rotating the Sub dial. When the change(s) are completed, press and hold in the MNU key for 2 seconds to save the change. If you do not want to save the change(s), press the MNU key momentarily. The radio will go back to its previous condition/situation. There are many setup items in the Menu, and they are grouped; the group name is displayed at the top left area of the list screen. It will generally be more convenient for you if you initially select the group, by rotating the Main Dial, and then select the item you want to work on. FT DX 9000MP/CONTEST DATA MANAGEMENT OPERATION MANUAL Page 19 AUDIO SCOPE AND OSCILLOSCOPE ABOUT THE AUDIO SCOPE AND OSCILLOSCOPE It is possible to show both the Audio Scope and the Oscilloscope displays simultaneously. With the Audio scope, the horizontal line represents frequency, and you can use this function check the frequency response within the TX bandwidth. In the Oscilloscope mode, the horizontal line represents time, and you can check the RX signal waveform within the RX bandwidth, as well as the TX wave form. EXPLANATION OF THE FUNCTION KEYS ON THE AUDIO SCOPE AND OSCILLOSCOPE SCREEN Here are the uses for the function keys when the Audio scope and Oscilloscope are displayed on the screen. [2/3. 5](MODE) The SCAN MODE for the left-side Audio Scope can be changed. By pressing this key, the mode changes as shown below. [. . . ] Included on this page will be the Menu Group, Menu Item Name, Menu Item Number, and the current status (setting) for each Menu item. Use the Main Tuning Dial, or the the [6/14]( )/[7/ 18]( ) keys, to select the Menu item you wish to work on. Use the CLAR/VFO-B knob, or the [4/7]( )/ [5]( ) keys, to change the setting of the selected Menu item. Press the MNU key is pressed for 2 seconds to save (within the transceiver) the new setting; the menu screen will close, and you will then return to the screen that was in use before entering the menu mode. [. . . ]