User manual YAESU PEP2000 UPDATE V0150 AND V11.53

[. . . ] Please follow the instructions in ADDENDUM: Page 7 and 9. Install the data file to PC 1. Down load the FT-2000 data file [FT-2000_PEP2000_11-30-09. zip] from the following website: http://www. yaesu. com/indexVS. cfm?cmd=DisplayProducts&ProdCatID=102&encProdID=66EA 91711DFB68C03DED4AD35153E12C&DivisionID=65&isArchived=0 2. Save the FT-2000 data file [FT-2000_PEP2000_11-30-09. zip] to the desktop on your computer. Unzip and Extract the contents of [FT-2000_PEP2000_11-30-09. zip] to the desktop of your computer. [. . . ] Note disregard the on screen instruction to [3. (7) When the loading process is complete, an [OK?] box will appear. (8) Turn off the main power switch, (or turn off the power supply for FT-2000D and wait a minute, until the capacitors discharge) and unplug the AC power cord. (10) Plug the AC power cord into the radio and turn the main power switch on the back of the radio to the ON position (or turn on the power supply for FT-2000D). Press and hold in the [FAST] and [LOCK] keys; while holding them in, press the front power switch to turn the radio on. This resets the radio and locks in the new software. (6) (12) Turn the radio off. The main CPU updating process is now complete. Follow the instructions below to update the EDSP. 8-pin mini-DIN PGM-SW 1. Connect a RS-232C straight cable to the CAT connector. Insert the 8-pin mini-DIN PMG-SW connector to FT-2000/D (PMG) jack. I choose the . sfl file of the version V0150 to write in and push WRITE of the screen. Remove the 8-pin mini-DIN PMG-SW and the RS-232C cable. Reset the radio to default. NOTE: for a more detailed description see the Main CPU programming. EDSP This procedure is used for uploading new EDSP Software into the FT-2000/D Amateur Transceivers, from your personal computer, using the RS-232C, DB9F to DB9F straight cable. Turn off the main power switch located on the back of the FT-2000 (or turn off the power supply for FT-2000D and wait a minute, until the capacitors discharge) and remove the AC power cord. Connect a serial RS-232C, DB9F to DB9F straight cable to the COM1 connector of your computer and the 9-pin CAT connector on the rear of the transceiver. If you use a USB to serial adapter, you might need to change the COM Port number. Main Power SW CAT 3. Reconnect the power cord and turn ON the main power switch located on the back of the FT-2000 (or turn ON the power supply for FT-2000D). While holding the [DNR][CONT][DNF] buttons, press the front power switch to turn the radio on. You will see [dSP Prg NO 1] on the radio display. 5. On your computer desk top open PEP2000_EDSP folder and find the EDSP-301 icon as shown below. Double-click the EDSP-301 icon, displayed on the Program Screen. 6. You will see AH025_V1153 out file displayed. [. . . ] Find the micro-switch on the pc board near the rear right hand corner when looking down at the bottom of the FT-2000/D. (See the attached photo. ) (2) (3) (4) (5) (6) Connect a serial cable RS-232C, DB9F to DB9F straight cable to the COM1 connector of your computer and the 9-pin CAT connector on the rear of the transceiver. If you use a USB to serial adapter, you might need to change the COM Port number. Switch the programming micro switch S3004 to on. [. . . ]