User manual YAKUMO TFT 17 XP

[. . . ] 4 4. 4 Menu features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4. 5 OSD menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. 6 Preset modes timing chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4. 7 Plug and play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Reorient/Relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer of an experienced radio/TV technician for help. English CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment. The use of a non-shielded interface cable with this equipment is prohibited. 15. Unplug this monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. If liquid has been spilled into the monitor. If the monitor has been exposed to rain or water. If the monitor does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls, may result in damage and will often require extensive NOTE: work by a qualified technician to restore the monitor to normal operation. If the monitor has been dropped or the cabinet has been damaged. W hen the monitor exhibits a distinct change in performance this indicated a need for service. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards. 17. Upon completion of any service or repairs to this monitor, ask the service technician to perform routine safety checks to determine that the monitor is in safe operating condition. 18. The socket outlet shall be near the equipment and shall be easily accessible. 19. The power supply cord is used as the main disconnect device. Chapter 1 Introduction 1. 1 General Information This monitor is a high-performance intelligent multi-scan TFT LCD color monitor. User friendly interface --- the easy and precise OSD control of multi- key button. Brief appearance --- elegant and compact housing. Footprint of all round tilting range --- employing sectional positioning , well Balanced in adjustment. Analog input, plug and play facilities --- to accept RGB signal, with modulated Frame rate control allowing over 20 different input formats. Chapter 2 Installation 2. 1 Install and uninstall the pedestal To attach the base to your monitor, please following the steps for installation of the pedestal as below: 1. 2 Features 1. Microprocessor based with OSD (On Screen Display) control. step 1 step 2 step 3 English 2. [. . . ] There is no SCREEN image Please check these items: The power cord is securely connected the monitor, the adaptor, and the wall outlet. Check the signal cable connection between the monitor and the computer. Adjust the brightness and contrast controls. Monitor in power saving mode. English Display image is too large or small Use the OSD controls to adjust Auto Setup. [. . . ]