User manual YAMAHA 02R-03D

[. . . ] DIGITAL RECORDING CONSOLE DIGITAL MIXING CONSOLE Table of Contents Introduction . 9. 02R with One ADAT (Timecode on Tape Track) . 12 02R with ADAT & JL Cooper Datasync-2 . 14 02R with Two ADATs & JL Cooper Datasync-2. [. . . ] After formatting, the sampling rate is determined by the formatted tape. Notes · The DA-88s must be powered up even when they are not being used. Failure to do so may cause an intermittent pumping noise on the 02R. · DA-88­A is set to MACHINE ID 0, DA-88­B to MACHINE ID 1, DA-88­C to MACHINE ID 2, and DA-88­D to MACHINE ID 3. Since DA-88­A works as the Control Master, it should be used for synchronized transport and locate operations. · The optional Tascam SY-88 Sync Board must be installed in DA-88­A to use SMPTE timecode and MTC. The other DA-88s do not require SY-88 Sync Boards and their tapes do not have to be striped with timecode. They are synchronized to DA-88­A via the PW-88S 15-pin sync cables. · The terminator bundled with a PW-88S sync cable should be connected to the SYNC OUT on DA-88­D to ensure reliable synchronization. · The rear panel of the SY-88 Sync Board has a DIP switch labeled MODE. Set internal switch 8 on the SY-88 board marked S2 to ON. · To use the MTC function, the SY-88 firmware must be version 3. 08 or higher. · On the Tascam (CD8-TD) card there is a DIP switch that should be set to 16-bit. This is the initial setting, but you should confirm it. This switch is for use with Tascam High-Bit recording applications. · Tascam 25-pin digital audio cables PW-88DL (5 m) and PW-88D (1 m), and the 15-pin PW-88S sync cable are available from Tascam. Yamaha 02R & 03D Applications Guide 02R Applications 33 Terminator SYNC OUT TDIF-1 ID=3 PW-88S 15-pin cable DA-88­C SYNC IN SYNC OUT TDIF-1 ID=2 SYNC IN PW-88S 15-pin cable DA-88­B SYNC OUT TDIF-1 ID=1 SYNC IN PW-88S 15-pin cable DA-88­A SYNC OUT TDIF-1 ID=0 WORD SYNC OUT (BNC) TIMECODE OUT (phono) TIMECODE INPUT (phono) DIGITAL RECORDING CONSOLE DA-88­D Optional SY-88 Sync Board installed Rear panel DIP switches 2 and 5=O Power Amp PW-88DL 25-pin cables x4 DAT Recorder DAT 1234 CD8-TD Interface Cards C-R Out Wordclock 2TR IN DIGITAL WORDCLOCK IN (BNC) (75=ON) Effects processor 88 STEREO OUT DIGITAL AUX SEND INPUT 17-24 Headphones TO HOST MIC/LINE Inputs 1­24 MIDI Sampler 02R Input Signal Select should be set to CARD SLOT 3 and CARD SLOT 4 MIDI keyboard Mic Figure 11 02R with Four DA-88s Yamaha 02R & 03D Applications Guide 02R 34 02R Applications 12 Two 02Rs with Four DA-88s This application shows how two 02Rs can be used with four Tascam DA-88s to create a 48-input, 32-track digital recording system. The 32 digital tape returns and 48 Mic/Line inputs provide up to 80 inputs at mixdown. The two 02Rs are cascaded together using a 25-pin straight cable and two CD8-CS Cascade cards, which are installed in Slot [3] of each 02R (could be Slot [4]). The cascade connection carries the eight buses, any four of the eight AUX buses, Stereo bus, and Solo bus. This allows both consoles to work together as one large 80-input mixing console. The master section of 02R­B is used for monitoring and two-track operations. The studio monitors and two-track recording equipment are also connected to this 02R. Connections · The Tascam (CD8-TD) cards must be screwed securely in place. Do not leave the screws out after installation as the cards will not be grounded correctly. [. . . ] Up to 50 mix scenes can be stored and recalled either manually or remotely via MIDI. · Two built-in effects processors eliminate the need for external processors. An all-in-one approach, compact size, and rack mounting mean that external equipment is kept to a simple minimum. · Digital recording to DAT is possible using the digital outputs, and a CD player can be connected digitally using the digital inputs. [. . . ]