User manual YAMAHA 225 3.1L VMAX-1998

[. . . ] In this Owner's Manual particularly important information is distinguished in the following ways. The Safety Alert Symbol means ATTENTION!YOUR SAFETY IS INVOLVED! cC A CAUTION indicates special precautions that must be taken to avoid damage to the outboard motor. NOTE: A NOTE provides key information to make procedures easier or clearer. [. . . ] L (US gal, Imp qt) Regular unleaded gasoline (Minimum 86) -- Yamalube 2-M outboard oil or another outboard motor manufacturer's factory-brand oil with TC-W3 rating oil injection system 1. 2 (1. 3, 1. 1) 10. 5 (11. 1, 9. 2)/18. 0 (19. 1, 15. 9) Hypoid gear oil (SAE90) 1, 150 (38. 9, 40. 5) Forward-Neutral-Reverse 1. 81 (29/16) Power trim/tilt M2 (66K) cm3 (cu. in. ) mm (in. ) NGK mm (in. ) 2-stroke, 76°V6 3, 130 (191. 0) 90. 0 × 82. 0 (3. 54 × 3. 23) C. D. I system (Microcomputer) BR8HS-10 0. 9~1. 0 (0. 035~0. 039) Remote control Electric start 512 675 182 12-35 Electronic Fuel Injection r/min kW (HP) @ r/min r/min 4, 500 ~ 5, 500 147. 1 (200) at 5, 000 r/min 675~725 mm (in. ) mm (in. ) mm (in. ) mm (in. ) kg (lb. ) 864 (34. 0) 562 (22. 1) 1, 685 (66. 3) 515 (20. 3) 231. 5 (510) Unit VX200TRC L L L amps at -18°C (-0. 4°F) amps at 0°C (32°F) minutes V-A (W) L (US qt, Imp qt) L (US qt, Imp qt) cm3 (US oz, Imp oz) 4-1 E VX225TRC VX250TRC -- 864 (34. 0) 562 (22. 1) 1, 685 (66. 3) 515 (20. 3) 231. 5 (510) 864 (34. 0) 562 (22. 1) 1, 685 (66. 3) 515 (20. 3) 231. 5 (510) 4, 500 ~ 5, 500 165. 5 (225) at 5, 000 r/min 675~725 2-stroke, 76°V6 3, 130 (191. 0) 90. 0 × 82. 0 (3. 54 × 3. 23) C. D. I system (Microcomputer) BR9HS-10 0. 9~1. 0 (0. 035~0. 039) Remote control Electric start 512 675 182 12-35 Electronic Fuel Injection 4, 500 ~ 5, 500 183. 9 (250) at 5, 000 r/min 700~760 2-stroke, 76°V6 3, 130 (191. 0) 90. 0 × 82. 0 (3. 54 × 3. 23) C. D. I system (Microcomputer) BR9HS-10 0. 9~1. 0 (0. 035~0. 039) Remote control Electric start 512 675 182 12-35 Electronic Fuel Injection Forward-Neutral-Reverse 1. 81 (29/16) Power trim/tilt M2 (66K) Forward-Neutral-Reverse 1. 75 (28/16) Power trim/tilt T Regular unleaded gasoline (Minimum 86) -- Yamalube 2-M outboard oil or another outboard motor manufacturer's factory-brand oil with TC-W3 rating oil injection system 1. 2 (1. 3, 1. 1) 10. 5 (11. 1, 9. 2)/18. 0 (19. 1, 15. 9) Hypoid gear oil (SAE90) 1, 150 (38. 9, 40. 5) Regular unleaded gasoline (Minimum 86) -- Yamalube 2-M outboard oil or another outboard motor manufacturer's factory-brand oil with TC-W3 rating oil injection system 1. 2 (1. 3, 1. 1) 10. 5 (11. 1, 9. 2)/18. 0 (19. 1, 15. 9) Hypoid gear oil (SAE90) 1, 150 (38. 9, 40. 5) 25 (2. 5, 18) 55 (5. 5, 40) 25 (2. 5, 18) 55 (5. 5, 40) 4-2 E EMU01369 TRANSPORTING AND STORING OUTBOARD MOTOR w Leaking fuel is a fire hazard. When transporting and storing the outboard motor, close the air vent screw and fuel cock to prevent fuel from leaking. 000859 EMK20210 TRAILERING OUTBOARD MOTOR The motor should be trailered and stored in the normal running position. If there is insufficient road clearance in this position, then trailer the motor in the tilt position using a motor support device such as a transom saver bar. For further details, consult your Yamaha dealer. w 8 Never get under the lower unit while it is tilted, even if a motor support bar is used. Severe injury could occur if the outboard accidentally falls. 8 USE CARE when transporting fuel tank, whether in a boat or car. DO NOT fill fuel container to maximum capacity. Gasoline will expand considerably as it warms up and can build up pressure in the fuel container. This can cause fuel leakage and a potential fire hazard. cC Do not use the tilt support lever/knob when trailering the boat. The outboard motor could shake loose from the tilt support and fall. If the motor can not be trailered in the down position, use an additional support device to secure it in the up position. Grease the spark plug threads and reinstall the spark plug(s) and torque to proper specification. (Refer to "CLEANING AND ADJUSTING SPARK PLUG". ) 2) Turn the engine over with the stop lanyard disconnected to work the fogging oil into the piston rings. This prevents the formation of condensation. For models with a remote tank, it may be necessary to manually override the control unit to completely fill the engine main tank. (Refer to "CHANGING GEAR OIL"). Inspect the oil for the presence of water which indicates a leaky seal. Seal replacement should be performed by an authorized Yamaha dealership prior to use. (Refer to "GREASING") 4-6 E EMK27110 Cleaning and Anti-corrosion Measure 1) Wash down the exterior of the outboard with fresh water and dry off completely. 2) Spray the engine's exterior with "Yamaha Silicone Protectant" (Part No. LUB-SILCNE-13-00). cC Do not spray when the engine is running. Also, do not spray near the silencer and oxygen sensor cover or into the engine. [. . . ] This list is complied from the purchase registrations sent to Yamaha Motor Corporation, U. S. A. by the selling dealer at the time of your purchase. If you should move after you have purchased your new outboard, please advise us of your new address by sending a postcard listing your outboard model name, engine serial number, dealer number (or dealer's name) as it is shown on your warranty identification, your name and new mailing address. Mail to: YAMAHA MOTOR CORPORATION, U. S. A. [. . . ]