User manual YAMAHA 25NE SERVICE MANUAL

[. . . ] 4 Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Attaching the Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 I About the Strap Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the user's manual, may cause interference harmful to the operation of other CANADA* THIS DIGITAL APPARATUS DOES NOT EXCEED THE "CLASS B" LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS SET OUT IN THE RADIO INTERFERENCE REGULATION OF THE CANADIAN DEPARTMENT OF COMMUNICATIONS. LE PRESENT APPAREIL NUMERIQUE N'EMET PAS DE BRUITS RADIOELECTRIQUES DEPASSANT LES LIMITES APPLICABLES AUX APPAREILS NUMERIQUES DE LA "CLASSE B" PRESCRITES DANS LE REGLEMENT SUR LE BROUILLAGE RADIOELECTRIQUE EDICTE PAR LE MINISTERE DES COMMUNICATIONS DU CANADA. · This applies only to products distributed by Yamaha Canada Music Ltd. · Ceci ne s'applique qu'aux produits distribués par Yamaha Canada Musique Ltée. 2 Your Silent Guitar will give you years of reliable service if you follow the simple rules given below: I Location Do not expose it to the following conditions to avoid deformation, discoloration, or more serious damage. · · · · · Direct sunlight (e. g. near a heat source, outside, or in a car during the daytime). Strong vibrations. I Power Supply · Turn the power switch OFF when not in use. · If you use an AC power adaptor, unplug the adaptor from the AC outlet if not to be used for an extended period of time. · If you use an AC power adaptor, make sure that the AC outlet you are using is easily accessible. · Do not place any excess force on the frame's rods. The rods may become damaged. Frame attachment screw 1 w Rod OPEN q First, insert the lower rod into the main body. w Then, insert the upper rod. 3. After confirming that both rods of the left frame are fully inserted, turn the attachment screws clockwise and secure the left frame to the Silent Guitar's main body. · When moving any movable parts, make sure that your fingers or hand do not become pinched in the parts. · Do not tighten the attachment screws when the frame is removed. It will result in the damage of parts, which will cause problems when re-attaching the frame. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. · THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. For that reason, we recommend that it be powered with the supplied AC power adaptor for normal use. Always turn the PHONES ON/OFF switch OFF before making AC power connections or replacing the battery. 2. Plug the adaptor's DC output cable into the Silent Guitar's DC IN jack, making sure the plug is firmly inserted into the jack. Plug the AC adaptor into a convenient wall AC power socket. · Battery power is automatically disconnected when the AC adaptor is connected. [. . . ] 3. Set the headphones ON/OFF switch, located on the right side of the control panel, to its "ON" position to supply power to the Silent Guitar. Insert the earphone plug into the headphone jack. When connecting the instrument to an external device, connect the external device to the PHONES jack using a cable with a stereo plug. The remaining procedures are the same as described above in the "Using the LINE OUT jack" section's steps 2 through 4. · When using a pair of headphones, do not operate at high volume levels for long periods of time. [. . . ]