User manual YAMAHA A0112T

[. . . ] A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. [. . . ] When placing the speaker on top of the TV, to prevent the speaker from falling, attach the provided fasteners at two points on the bottom of the speaker and on the top of the TV. Notes Do not place the speaker on top of a TV whose area is smaller than the bottom of the speaker. If placed, the speaker may fall and cause injury. Do not place the speaker on top of a TV if the top is inclined. Do not touch the adhesive surface after peeling off the seal as this will weaken its adhesive strength. Thoroughly wipe clean the surface where the fastener is to be applied. Note that adhesive strength is weakened if the surface is dirty, oily or wet and that this may cause the center speaker to fall. Fastener Peel off the seal E-4 English Mounting the main/rear/center speakers (and rear center speaker for A0112T) on the wall 1 Tapping screw (Available at the hardware store) Diam. 3. 5 to 4 mm You can mount the main, rear and/or center speakers (and/ or rear center speaker for A0112T) on a wall. To mount the speakers on a wall, use the holes of the brackets attached on the speakers' back panels. Main/rear/rear center (for A0112T) Min. 20 mm 4 mm Holes Wall/ wall support 2 Main/rear/rear center (for A0112T) Center 26 mm 1 Fasten two screws into a firm wall or wall support at the interval shown below. Main/rear/rear center (for A0112T) . . . . . . . . . . * To connect with a YAMAHA DSP amplifier (or AV receiver), connect the SUBWOOFER (or LOW PASS etc. ) terminal on the rear of the DSP amplifier (or AV receiver) to the L/MONO INPUT terminal of the subwoofer. * To connect the subwoofer to the SPLIT SUBWOOFER terminals on the rear of the DSP amplifier, connect them to both the left L/MONO and right R INPUT terminals of the subwoofer. Note When connecting to a monaural line output terminal of the amplifier, connect to the L/MONO INPUT terminal. E-8 English How to connect speaker cables to the input terminals of the speakers For connections, keep the speaker cables as short as possible. Do not bundle or roll up the excess part of the cables. If the connections are faulty, no sound will be heard from the speakers. Main speakers Center speaker Use the provided speaker cables (4 m). One side of the speaker cable is red and the other side is black. Connect the (+) terminals on both the speaker and the amplifier using the red side of the cable. Connect the (­) terminals on both components using the black side. Red: positive (+) Black: negative (­) Before connecting Remove the insulation coating at the extremity of each speaker cable by twisting the coating off. How to Connect: Red 1 Press and hold the terminal's tab, as shown in the figure. 2 Insert the bare wire. 3 Release your finger from the tab to allow it to lock securely on the cable's wire end. Black 4 Test the firmness of the connection by pulling lightly on the cable at the terminal. Note Do not let the bare speaker wires touch each other as this could damage the speaker or the amplifier, or both of them. Rear speakers Rear center speaker (for A0112T) Use the provided speaker cables (15 m). [. . . ] 16 cm (6-1/2") cone woofer <NX-430P> . . . . . . . . . . . . . . . . . . . . . . . Coaxial 2-way [5 cm (2") cone <NX-C430> and 1. 3 cm (1/2") dome] speaker x 1 5 cm (2") full range cone speaker x 1 . . . . . . . . . . . . . . . . . . . . . . Coaxial 2-way [5 cm (2") cone and 1. 3 cm (1/2") dome] speaker x 1 5 cm (2") full range cone speaker x 2 Amplifier Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 W/5 Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]