User manual YAMAHA AD8HR

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual YAMAHA AD8HR. We hope that this YAMAHA AD8HR user guide will be useful to you.

Lastmanuals help download the user guide YAMAHA AD8HR.


Mode d'emploi YAMAHA AD8HR
Download

You may also download the following manuals related to this product:

   YAMAHA AD8HR (714 ko)
   YAMAHA AD8HR NOTES ON RACK MOUNTING THE UNIT (164 ko)
   YAMAHA AD8HR NOTES ON RACK-MOUNTING THE UNIT (191 ko)

Manual abstract: user guide YAMAHA AD8HR

Detailed instructions for use are in the User's Guide.

[. . . ] Owner's Manual Thank you for choosing the Yamaha AD8HR AD converter with remote microphone preamp. The AD8HR is an eight-channel AD converter equipped with remote microphone preamps that feature 96kHz, 24-bit linear AD conversion, 128-times oversampling, and a dynamic range of 110dB. Its input section features balanced XLR connectors, high-quality mic preamps, +48V phantom power, and support for both mic and linelevel inputs. The output section supports the AES/EBU format and features a high sampling frequency of 88. 2/96kHz. [. . . ] While the indicator is flashing rapidly, press the [WORD CLOCK] button again. The AD8HR switches to the selected wordclock source and the flashing wordclock indicator stays lit. The indicator of the previously-selected wordclock source turns off. If you do not press the [WORD CLOCK] button again before the indicator stops flashing (it will flash for five seconds), the new selection is cancelled and the previous wordclock is selected. If the AD8HR is not locking to the selected wordclock source, the corresponding wordclock source indicator flashes. NOTE: The only word clock source available via the AES/EBU connection is the IN signal of DIGITAL OUT A channels 1/ 2. While the indicator is flashing rapidly, press the [+48V] button again. The phantom power for the selected channels turns on, and the corresponding channel [+48V] indicators and the [+48V] button indicator light up. If you do not press the [+48V] button again before the indicator stops flashing (it will flash for five seconds), the setting is cancelled. Adjusting the Gain Follow the steps below to adjust the channel gain in 1dB steps. 1 2 Press the Channel Select button to select a channel. The selected channel's Channel Select button indicator lights up and the Gain display indicates the gain value. Rotate the Gain control to adjust the gain You can adjust the gain in the range of 10dB through ­62dB in 1dB steps. NOTE: · While adjusting the gain, you may notice that the sound is briefly interrupted. The internal setting is switched in steps of 6 dB, and the sound is momentarily muted so that the noise will not be created during the switching operation. · The PAD will be switched on or off internally when the gain is adjusted between -14 dB and -13 dB. Keep in mind that noise may be generated if there is a difference between the Hot and Cold output impedance of the external device connected to the INPUT connector when using phantom power. Setting the Phantom Power Follow the steps below to turn the +48V phantom power for each channel on or off. NOTE: You can also turn the phantom power for all channels on or off simultaneously (not individual channels) using the [+48V MASTER] switch. When the [+48V MASTER] switch is turned off, the phantom power is not supplied to channels even if the [+48V] button is turned on for the channels. Adjusting the Gain Trim (Gain Correction) Follow the steps below to correct the channel gain in 0. 1dB steps. The output level of each channel has been calibrated in the factory. Typically, you will not have to correct the setting. NOTE: In the factory, the level has been set to the optimum value and the initial level varies with each channel. This setting is reset to the factory value when you initialize the backup memory. 1 Press the Channel Select buttons to select the channels. The selected channels' Channel Select button indicators light up. The channel +48V indicator lights up when the +48V phantom power for the selected channels is turned on. [. . . ] Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 POLAND Yamaha Music Central Europe GmbH Sp. z. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE YAMAHA AD8HR

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual YAMAHA AD8HR will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag