User manual YAMAHA AO8-AO8-DA8

[. . . ] Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit "OFF" and "ON", please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. [. . . ] · Do not remove the unit's cover. If you think internal inspection, maintenance, or repair is necessary, contact your dealer. Doing so is a fire and electrical shock hazard. · When rack-mounting the unit, allow enough free space around the unit for normal ventilation. This should be: 10 cm at the sides, 15 cm behind, and 30 cm above. · For normal ventilation during use, remove the rear of the rack or open a ventilation hole. · If the airflow is not adequate, the unit will heat up inside and may cause a fire. · This unit has ventilation holes at the top, bottom, and rear to prevent the internal temperature rising too high. Blocked ventilation holes are a fire hazard. · Hold the power cord plug when disconnecting it from an AC outlet. A damaged power cord is a potential fire and electrical shock hazard. · Do not touch the power plug with wet hands. Doing so is a potential electrical shock hazard. · The digital circuits of this unit may induce a slight noise into nearby radios and TVs. If noise occurs, relocate the affected equipment. · XLR-type connectors are wired as follows: pin 1: ground, pin 2: hot (+), and pin 3: cold (-). Rack Mounting Caution If the unit is rack mounted and transported regularly, for example, when on a tour, we recommend that the rear of the unit be supported by fitting a pair metal brackets, one each side. The following drawing provides the information necessary to make such brackets. Note that only one bracket is shown here and the bracket for the other side must be bent in the opposite direction. 2-R2 2-R2 (82. 1) 76. 2 31. 75 R5 3. 1 20. 5 200 0 5. 9 4- ø 6. 5 0 7. 5 36. 5 14. 5 t = 1. 6 134 0 8 12 R2 3 86. 5 44. 45 Thank you for choosing the AO8 analog output box, or the AO8-DA8 analog output unit, specifically designed for the Yamaha PM1D digital audio mixing system. The AO8 converts digital signal input from the DSP1D/DSP1D-EX engine (controlled via the CS1D control surface) to analog signals. Up to six AO8s can be connected to each DSP1D/DSP1D-EX. Be sure to ask an authorized Yamaha service engineer to install the card and set up the unit. Never perform installation and setup by yourself. Cards installable on the AO8 analog output box : LMY4-DA -- DA card AO8-DA8 analog output unit : AO8 analog output box that has eight LMY-4-DA cards installed s Front panel OUTPUT UNIT ID 1 INPUT SELECTOR 1 2 3 4 5 6 7 8 A UNIT NO. [. . . ] . " "_. A. " means that the control signal from the CS1D has changed the setting to "A" " " means that the control signal from the CS1D has changed the setting to "B. " During this time period, you can connect or disconnect the cable from the unselected output connector. If you set the INPUT SELECTOR switch so that it matches the setting made via the control signal from the CS1D, "O. x. " lights up continuously. B INPUT SELECTOR switch Use this switch to select an input source from the INPUT A or B connector on the rear panel. During the Mirror mode operation, the control signal sent from the CS1D has priority, and the INPUT SELECTOR switch is disabled. In this case, the OUTPUT UNIT ID indicator shows the status. [. . . ]