User manual YAMAHA AV-35

[. . . ] To prevent fire or electric shock, do not expose the speakers to rain or water. To prevent the enclosure from warping or discoloring, do not place the speakers where they will be exposed to direct sunlight or excessive humidity. Avoid installing the speakers where foreign objects may fall onto them and/or where they may be exposed to liquid dripping or splashing. Do not place the following objects on top of the speakers: Other components, as they might cause damage and/or discoloration on the surface of the speakers. [. . . ] The subwoofer emits reinforcing low frequencies on your audio system. Note In this speaker package, the same speakers (NX-E130) are used for the front and rear speakers (and rear center speaker for NS-P116). Rear center speaker (for NS-P116): Precisely between the rear speakers. Subwoofer: The position of the subwoofer is not so critical because low bass tones are not highly directional. Refer to "Placing the subwoofer" on page 4 for a recommended positioning of the subwoofer. Front R Center Front L Subwoofer TV-set Front L Center Front R Subwoofer Rear center (for NS-P116) Rear L Rear R Rear L Rear center (for NS-P116) Rear R These speakers feature a magnetically shielded design, but there is still a chance that placing them too close to a TV set might impair picture color. Should this happen, move the speakers away from the TV set. E-3 Placing the subwoofer Å i It is recommended to place the subwoofer on the outside of either the right or the left front speaker. i is also possible, however, if the subwoofer system is placed directly facing the wall, the bass effect may die because the sound from it and the sound reflected by the wall may cancel out each other. To prevent this from happening, face the subwoofer system at an angle as shown in fig. Note There may be a case that you cannot obtain enough superbass sounds from the subwoofer when listening in the center of the room. This is because "standing waves" have been developed between two parallel walls and they cancel the bass sounds. In such a case, face the subwoofer obliquely to the wall. It also may be necessary to break up the parallel surfaces by placing bookshelves etc. * To connect the subwoofer to the SPLIT SUBWOOFER terminals on the rear of the DSP amplifier, connect them to both the left L/MONO and right R INPUT terminals of the subwoofer. Note When connecting to a monaural line output terminal of the amplifier, connect to the L/MONO INPUT terminal. How to connect speaker cables For connections, keep the speaker cables as short as possible. Do not bundle or roll up the excess part of the cables. If the connections are faulty, no sound will be heard from the speakers. One side of the provided speaker cable has a white broken line and the other side has no line. Connect the (+) terminals on both the speaker and the amplifier using the side with a white broken line. Connect the (­) terminals on both components using the side with no line. Before connecting Remove the insulation coating at the extremity of each speaker cable by twisting the coating off. How to Connect: 1 Press and hold the terminal's tab, as shown in the figure. 2 Insert the bare wire. 3 Release your finger from the tab to allow it to lock securely on the cable's wire end. 4 Test the firmness of the connection by pulling lightly on the cable at the terminal. Red: positive (+) Black: negative (­) White broken line Note Do not let the bare speaker wires touch each other as this could damage the speaker or the amplifier, or both of them. E-8 English USING THE SUBWOOFER (SW-P130) Controls and their functions SUBWOOFER SYSTEM YST SW005 1 Port Front panel Rear panel VOLUME VOLUME 0 AUTO STANDBY 10 POWER ON HIGH LOW OFF 6 /MONO 2 OFF INPUT 0 AUTO STANDBY HIGH LOW OFF 10 4 3 110V-120V 220V-240V VOLTAGE SELECTOR 220V-240V 110V-120V VOLTAGE SELECTOR POWER ON 5 INPUT /MONO OFF 1 Power indicator Lights up GREEN when the POWER switch (2) is pressed in to the ON position and goes off when set to the OFF position. * Standby mode If the POWER switch (2) is pressed in to the ON position and the AUTO STANDBY switch (4) is set to the HIGH or LOW position, this indicator lights up RED when no signal is received by the subwoofer. POWER switch Press this switch to the ON position to turn on the power of the subwoofer. When the power of the subwoofer is on, the power indicator (1) on the front panel lights up GREEN. [. . . ] The AUTO STANDBY switch is set to the OFF position. The level of input signal is too low. The subwoofer does not turn into the standby mode automatically. There is an influence of noise generated from external appliances etc. The AUTO STANDBY switch is set to the OFF position. The subwoofer turns into the standby mode unexpectedly. There is an influence of noise generated from external appliances etc. E-13 SPECIFICATIONS NX-E130, NX-C130 Type . . . . . . . . . [. . . ]