User manual YAMAHA C115HP-2000

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] The [SIGNAL/PEAK] indicators also light red to indicate excessive input level at the corresponding input. If excessive input level is indicated either reduce the output level of the connected source, or reduce the C115HP-2000 input sensitivity via the appropriate rear-panel [PAD] switch or by reducing the [INPUT GAIN] setting via the C115HP-2000 Manager application. ) [SIGNAL/PEAK] Indicators These indicators light green when a signal is detected at OUTPUT 3 and 4. The [SIGNAL/PEAK] indicators also light red to indicate excessive output level at the corresponding output. If excessive output level is indicated, reduce the input level or output level. 5 Level Knobs These knobs adjust the input level of the corresponding mono channels. !Level Knobs These knobs adjust the output level from the corresponding output channels. STEREO INPUT Section 6 Matrix Indicators The outputs to which each stereo input are assigned are displayed by orange indicators. @ MEMORY [A] ­ [D] Buttons · Recalling Memories To recall a memory press and hold one of the MEMORY buttons for about 2 seconds ­ the button's indicator will light and the mix settings assigned to that memory will be recalled. Settings are stored in the C115HP-2000 memories via the C115HP-2000 Manager application. Memories A through D all contain the same settings when the unit is initially shipped from the factory. · Switching Modes To start the unit in C115HP-2000 Manager mode, hold the MEMORY [D] button while turning the [POWER] switch ON. The unit starts up in the "normal" mode if the power is turned on while the MEMORY [D] button is not held. C115HP-2000 Manager Mode This mode allows communication with the C115HP-2000 application. Communication with AMX and similar external controllers cannot occur in this mode. This is the unit's normal operating mode. If these measures are not observed sudden high-level noise bursts can potentially damage equipment and even the hearing of people in the area. · · OUTPUT Section ) Euroblock Connectors These balanced output connectors are for connection to power amplifiers and other output devices. The A connector outputs the left-channel signal, and the B connector outputs the rightchannel signal. OUTPUT 1 and 2 can also be assigned for mono output via the C115HP-2000 Manager application. Refer to page 13 for instructions on connecting to the Euroblock connectors. C115HP-2000 Owner's Manual 11 Connections System Example Computer Cassette deck Microphone MD player CD recorder Wireless microphone Wireless tuner AMX or similar external controller 1 2 3 4 Power amplifier 5 6 7 8 External control input/ output device Zone 1 speakers Power amplifier Zone 2 speakers Zone 3 speakers Zone 4 speakers 12 C115HP-2000 Owner's Manual Connections Connectors and Cables [MONO INPUT] and [OUTPUT] Connectors (3-pin Euroblock) Connect external microphones, amplifiers and other devices to the rear-panel [MONO INPUT] and [OUTPUT] connectors via cables fitted with the supplied 3-pin Euroblock plugs. Follow the procedure outlined in this section to attach the Euroblock plugs to the appropriate cables. Euroblock Pin Assignments Pin No. 1 2 1 2 3 3 Signal name HOT COLD GND Euroblock Plug Connection NOTE · A "minus" type screwdriver with a blade width of approximately 3 millimeters is recommended for Euroblock connector attachment. 3mm 1 Strip the insulation from cables to be attached to a Euroblock plug as shown below. Shielded cable 7mm 30mm CAUTION · · Be sure to use shielded cables. Do not tin (plate with solder) the exposed sections of the cable. Use balanced lines to connect microphones and similar sources to the [MONO INPUT] connectors. Wire balanced cables as shown in the diagram below. XLR-3-11C (or equivalent) 2 Loosen the terminal screws. Loosen Slotted screwdriver 1 3 2 1 Terminal screw Euroblock plug 2 3 When an amplifier to be connected to the OUTPUT connector has balanced XLR type inputs, wire the connection cable as shown in the diagram below. XLR-3-12C (or equivalent) 3 Insert the cables. 1 3 2 1 2 4 3 Securely tighten the terminal screws. Pull the cables (not too strongly) to confirm that they are securely connected. 5 Connect the Euroblock plug to the C115HP-2000 Euroblock connector. C115HP-2000 Owner's Manual 13 Connections [REMOTE] Connector (RS-232C) Connect to this connector when controlling the C115HP-2000 from the C115HP-2000 Manager application or an external AMX/Crestron controller. Use an RS-232C cross cable for connection. Connector Pin Assignments 12345 [GPI] Connector (25-pin D-sub) External GPI (General Purpose Interface) control devices can be connected to this connector to allow input and output of remote control signals. The C115HP-2000 GPI port has eight inputs and eight outputs, plus a dedicated "POWER MONITOR" output that indicates the unit's ON/OFF status. [. . . ] By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. [For business users in the European Union] If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] This symbol is only valid in the European Union. [. . . ]