User manual YAMAHA CBX-T3

[. . . ] Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. [. . . ] Holding down C accesses the secondary or "hidden" functions, and you may inadvertently execute one of these functions by playing the keyboard while continuing to hold down C. NOTE s This function does not "wrap around. " In other words, you cannot go back to program number 127 when at 0, or advance to program number 0 when at 127. 10 Using the CBX-T3 -- Basic Operations q PITCH Wheel This Wheel controls Pitch Bend on the connected MIDI device. The Wheel's maximum/minimum positions can be reversed. (See page 20. ) q ASSIGNABLE Wheel When the CBX-T3 is turned on, this Wheel is set to control Modulation Depth on the connected MIDI device. It can be set to control other functions; see page 18 for details. The Wheel's maximum/minimum positions can be reversed. (See page 20. ) IN MIDI OUT CONTROLLER NUMBER LIST 1 2 4 5 6 7 8 10 CONTROL CHANGE MODULATION DEPTH BREATH CONTROL FOOT CONTROL PORTAMENTO TIME DATA ENTRY MAIN VOLUME BALANCE CONTROL PANPOT 11 64 65 66 67 69 71 72 EXPRESSION HOLD1(DAMPER) PORTAMENTO SOSTENUTO(CHORD HOLD) SOFT PEDAL HOLD2 (FREEZE) HARMONIC CONTENT RELEASE TIME 73 74 84 91 92 93 94 95 ATTACK TIME BRIGHTNESS PORTAMENTO CONTROL REVERB DEPTH TREMOLO DEPTH CHORUS DEPTH VARIATION DEPTH PHASER DEPTH (RPN) 120 PITCH BEND SENSITIVITY 121 FINE TUNING 122 COARSE TUNING (NRPN) 123 VIBRATO RATE 124 VIBRATO DEPTH 125 VIBRATO DELAY 126 127 128 129 130 131 132 133 FILTER CUTOFF FREQUENCY FILTER RESONANCE EG ATTACK TIME EG DECAY TIME EG RELEASE TIME DRUM FILTER CUTOFF FREQUENCY DRUM FILTER RESONANCE DRUM EG ATTACK RATE 134 135 136 137 138 139 140 141 PITCH ASSIGNABLE SEQUENCER PROGRAM BANK PROGRAM TEMPO SELECT CHANGE GM ON RESET SOUND OFF XG ON MERGE ON/OFF SYSTEM MIDI CH FIXED VELOCITY WHEEL ASSIGN RPN CONTROLLER NRPN DRUM NUMBER TRANSPOSE 1 2 3 4 5 6 SHIFT STOP CONTINUE START OCTAVE OCTAVE SHIFT OCTAVE RESET q Changing the Octave Setting You can easily change the octave range of the CBX-T3 keyboard while playing. In this way the three-octave keyboard can cover the entire range of MIDI notes, from C-2 to G8 (0-127). To shift the keyboard up one octave, press M. To shift the keyboard down one octave, press N. When the octave is changed, the LEDs rapidly flash one, two, three or four times, according to the selected octave range. For messages beginning with zeroes, the first zeroes can be omitted. Examples: * 3 J: results in a value of MSB = 00, LSB = 03. * 0 3 J: results in a value of MSB = 00, LSB = 03. * 1 0 3 J: results in a value of MSB = 01, LSB = 03. * 0 1 0 3 J: results in a value of MSB = 01, LSB = 03. NOTE s The order of MSB and LSB entry can be reversed. (See page 20. ) Value Entry -- Some Specific Examples and Anomalies q Using K Examples: * 1 2 K: results in a value of 12. * 3 a K: results in a value of 310, which is ignored since it is outside the legal value range (0-255). NOTES ON THE BASIC OPERATION s If you inadvertently press two or more function keys while performing a function, the last pressed key has priority. s If, after entering a value, you press another function key before pressing L, the value will be cancelled. s If you enter a value that is outside of a function's range, it will be ignored. Legal messages can be one byte in length (a value from 0-255). 13 Using the CBX-T3 -- Basic Operations Setting the Functions This section shows by example the operations for the basic functions. * Unless indicated otherwise, L refers to either of the ENTER keys, J or K. However, when you wish to enter a decimal value, make sure to press K. [. . . ] CBX-T3 operations that start before or end after the System Exclusive message will be incomplete. To avoid this problem, be careful not to execute operations from both the CBX-T3 and the external device at the same time. Also: * If the Merge function is not needed, turn Merge off or disconnect the MIDI cable. * Do not operate the CBX-T3 during reception of large System Exclusive messages, such as bulk dumps. q Response of the CBX-T3 During MIDI Errors When a MIDI reception error occurs (such as buffer full, Active Sensing, interruption of System Exclusive, etc. ), the CBX-T3 responds as follows: 1. [. . . ]